Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.04–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Main body ECU (multiplex network body ECU) main wire or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or power distribution box assembly

·

Main body ECU (multiplex network body ECU) or power distribution box assembly ground circuit

·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly



WIRING DIAGRAM

C441292E05
5.5,0.927 5.75,1.115 0.25,0.188 10 false I3 5.823,1.438 6.438,1.635 0.615,0.198 10 false CANL 5.833,0.833 6.448,1.031 0.615,0.198 10 false CANH 0.188,1.875 0.583,2.063 0.396,0.188 10 false Q62 0.177,2.031 2.583,2.24 2.406,0.208 10 false No. 11 Global CAN Junction Connector 1.563,1.406 1.813,1.604 0.25,0.198 10 false 8 1.563,0.833 1.813,1.031 0.25,0.198 10 false 2 5.521,0.698 5.771,0.896 0.25,0.198 10 false 2 5.521,1.281 5.771,1.479 0.25,0.198 10 false 1 5.5,3.115 5.75,3.313 0.25,0.198 10 false 26 5.469,3.344 5.833,3.563 0.365,0.219 10 false MB 5.844,3.323 6.458,3.521 0.615,0.198 10 false BECU 5.844,4.146 6.458,4.344 0.615,0.198 10 false IGR 5.5,3.927 5.75,4.125 0.25,0.198 10 false 27 4.365,4.302 5.448,4.51 1.083,0.208 10 false ECU-IGR NO.2 3.552,4.885 4.635,5.094 1.083,0.208 10 false IGR-NO.2 2.75,3.333 3,3.531 0.25,0.198 10 false 5E 2.76,3.094 3.01,3.292 0.25,0.198 10 false 23 2.75,4.167 3,4.365 0.25,0.198 10 false 5K 2.802,3.948 3.052,4.146 0.25,0.198 10 false 1 2.771,4.396 3.083,4.625 0.313,0.229 10 false 11 2.76,4.615 3.01,4.813 0.25,0.198 10 false 5B 0.99,4.146 2.438,4.406 1.448,0.26 10 false from Battery 0.396,4.604 1.75,5.135 1.354,0.531 10 false from Certification ECU (Smart Key ECU Assembly) 5.833,5.719 6.448,5.917 0.615,0.198 10 false GND1 5.833,6.323 6.448,6.521 0.615,0.198 10 false GND2 5.479,5.51 5.729,5.708 0.25,0.198 10 false 13 5.49,6.104 5.74,6.302 0.25,0.198 10 false 14 2.75,5.719 3,5.917 0.25,0.198 10 false 5C 2.771,5.49 3.021,5.688 0.25,0.198 10 false 41 2.76,6.083 3.01,6.281 0.25,0.198 10 false 36 2.75,6.313 3,6.51 0.25,0.198 10 false 5C 3.031,7 4.427,7.406 1.396,0.406 10 false Power Distribution Box Assembly 5.146,6.979 6.771,7.406 1.625,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,4.156 5.833,4.375 0.365,0.219 10 false MB 5.458,5.729 5.823,5.948 0.365,0.219 10 false MB 5.469,6.323 5.833,6.542 0.365,0.219 10 false MB 4.365,3.51 5.448,3.719 1.083,0.208 10 false ECU-DCC NO.2 0.979,3.302 2.427,3.563 1.448,0.26 10 false from Battery 5.5,1.521 5.75,1.708 0.25,0.188 10 false I3



CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I3)Location & Routing

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

I3-2 (CANH) - I3-1 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

b.

Connect the power distribution box assembly connectors.


c.
C434125C01
1.542,0.594 1.927,0.844 0.385,0.25 3.052,1.635 2.927,1.229 true 2.573,1.625 2.813,1.219 true 1.427,1.635 1.667,1.229 true 1.875,1.635 1.75,1.229 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.646,0.656 1.958,0.854 0.313,0.198 10 false z13 1.219,1.677 1.708,1.823 0.49,0.146 10 false GND1 2.99,1.677 3.344,1.854 0.354,0.177 10 false IGR 1.719,1.677 2.208,1.823 0.49,0.146 10 false GND2 2.417,1.677 2.906,1.823 0.49,0.146 10 false BECU
*a Component without harness connected
(to Power Distribution Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-13 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
MB-14 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



d.

Reconnect the cable to the negative (-) battery terminal.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MB-26 (BECU) - Body ground Always 11 to 14 V
MB-27 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 5C and 5K power distribution box assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5C-36 - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
5C-41 - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5K-1 - Body ground Always 11 to 14 V
5E-23 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5B-11 - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG