Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › ENGINE
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467568 ENGINE G

V35A-FTS ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running or the ignition switch ON.


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that there is no dirt, blockage, and/or damage to the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 88310A 7.INSPECT NO. 1 V BELT (COOLER COMPRESSOR TO CRANKSHAFT PULLEY)

Hide 16620D 8.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16601 9.INSPECT V-RIBBED BELT TENSIONER SUB-ASSEMBLY

Hide 13750 10.INSPECT VALVE LASH ADJUSTER ASSEMBLY

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a valve lash adjuster inspection.


Hide 11.INSPECT IGNITION TIMING

a.

Warm up the engine and stop the engine.

NOTICE:

A warmed up engine should have an engine coolant temperature of over 80°C (176°F), and an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.



b.

Connect the GTS to the DLC3.


c.

Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.

Powertrain > Engine > Data List
Tester Display
Ignition Timing Cylinder #1
50003 372 213

d.

Monitor Ignition Timing Cylinder #1 of the Data List.

Standard ignition timing:

8 to 25° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transmission should be in park.




e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.

Powertrain > Engine > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Ignition Timing Cylinder #1
50004 372 22 213

f.

Monitor Ignition Timing Cylinder #1 of the Data List.

Standard ignition timing:

8 to 12° BTDC at idle



g.

Disconnect the GTS from the DLC3.


h.

Check that the ignition timing advances immediately when the engine speed is increased.


Hide 12.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

d.

Read the value displayed on the GTS.

Standard idle speed:

600 to 800 rpm


NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transmission should be in park.




e.

Disconnect the GTS from the DLC3.


Hide 13.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.

NOTICE:

A warmed up engine should have an engine coolant temperature of over 80°C (176°F) and an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.



b.

Connect the GTS to the DLC3.


c.

Check for DTCs.


d.
A485360

Disconnect the 4 connectors.


e.

Remove the 6 spark plugs.

Click hereGeneral>MAINTENANCE>V35A-FTS SPARK PLUG>REMOVAL


f.

Inspect compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Depress and hold the brake pedal, and turn the ignition switch to ON. Then check the compression pressure.

Standard Compression Pressure:

1300 kPa (13.3 kgf/cm2, 189 psi)


Minimum Compression Pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Pressure Difference between Each Cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


NOTICE:
·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iii.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





g.

Install the 6 spark plugs.

Click hereGeneral>MAINTENANCE>V35A-FTS SPARK PLUG>INSTALLATION


h.

Connect the 4 connectors.


i.

Clear the DTCs.


Hide 14.INSPECT CO/HC

HINT:

This is a check for determining whether or not the idle CO/HC complies with regulations.


a.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


b.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.


c.

Immediately check CO/HC concentration at idle and/or 2500 rpm.

HINT:
·

When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

·

If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.



i.

Check the DTCs.


ii.

See the table below for possible causes, then inspect and correct the applicable causes if necessary.

CO HC Symptom Causes
Normal High Rough idle
1.

Faulty ignitions

-

Incorrect timing

-

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaky intake and exhaust valves

4.

Leaky cylinder


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks

-

PCV hose

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air filter

2.

Plugged PCV valve

3.

Faulty fuel SFI system

-

Faulty fuel pressure

-

Defective engine coolant temperature sensor

-

Faulty ECM

-

Faulty fuel injector assembly

-

Faulty throttle position sensor (built into throttle with motor body assembly)

-

Faulty mass air flow meter