The condition of the windshield wiper switch assembly is detected and sent to the steering sensor in this circuit.
for LHD:
for RHD:
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper OFF Switch | Windshield wiper switch assembly (OFF position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in OFF position ON: Windshield wiper switch assembly in OFF position |
- |
| Wiper Auto/Int Switch | Front wiper switch AUTO*1 or INT*2 position signal | OFF or ON | OFF: Front wiper switch not in AUTO*1 or INT*2 position ON: Front wiper switch in AUTO*1 or INT*2 position |
- |
| Wiper Lo Switch | Windshield wiper switch assembly (LO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in LO position ON: Windshield wiper switch assembly in LO position |
- |
| Wiper Hi Switch | Windshield wiper switch assembly (HI position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in HI position ON: Windshield wiper switch assembly in HI position |
- |
| Wiper Mist Switch | Windshield wiper switch assembly (MIST position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in MIST position ON: Windshield wiper switch assembly in MIST position |
- |
| Washer Switch | Windshield wiper switch assembly (washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (washer switch) in OFF position ON: Windshield wiper switch assembly (washer switch) in ON position |
- |
| Rear Wiper INT Switch | Windshield wiper switch assembly (rear wiper switch INT position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in INT position ON: Windshield wiper switch assembly (rear wiper switch) in INT position |
- |
| Rear Wiper ON Switch | Windshield wiper switch assembly (rear wiper switch ON position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in ON position ON: Windshield wiper switch assembly (rear wiper switch) in ON position |
- |
| Rear Washer Switch | Windshield wiper switch assembly (rear washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear washer switch) in OFF position ON: Windshield wiper switch assembly (rear washer switch) in ON position |
- |
| Intermittent Time Volume (Shortest) | Auto sensitivity adjustment switch condition*1 Intermittent time adjustment switch condition*2 |
OFF or ON | OFF: Washer switch not in P4 position ON: Washer switch in P4 position |
*3 |
| Intermittent Time Volume (Shorter) | Auto sensitivity adjustment switch condition*1 Intermittent time adjustment switch condition*2 |
OFF or ON | OFF: Washer switch not in P3 position ON: Washer switch in P3 position |
*3 |
| Intermittent Time Volume (Longer) | Auto sensitivity adjustment switch condition*1 Intermittent time adjustment switch condition*2 |
OFF or ON | OFF: Washer switch not in P2 position ON: Washer switch in P2 position |
*3 |
| Intermittent Time Volume (Longest) | Auto sensitivity adjustment switch condition*1 Intermittent time adjustment switch condition*2 |
OFF or ON | OFF: Washer switch not in P1 position ON: Washer switch in P1 position |
*3 |
*1: w/ Auto Wiper System
*2: w/o Auto Wiper System
*3: Refer to Inspection for each position of the switch.
Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>INSPECTION
| Tester Display |
|---|
| Wiper OFF Switch |
| Wiper Auto/Int Switch |
| Wiper Lo Switch |
| Wiper Hi Switch |
| Wiper Mist Switch |
| Washer Switch |
| Rear Wiper INT Switch |
| Rear Wiper ON Switch |
| Rear Washer Switch |
| Intermittent Time Volume (Shortest) |
| Intermittent Time Volume (Shorter) |
| Intermittent Time Volume (Longer) |
| Intermittent Time Volume (Longest) |
The GTS display changes correctly in response to the windshield wiper switch assembly operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Disconnect the I51 steering sensor connector.
Disconnect the I94 windshield wiper relay assembly connector.
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I51,I94,I3)Location & Routingewd_type=routing;type=c,c,c;code=I51,I94,I3 |
||
| I51-2 (2S) - I94-3 (2S) | Always | Below 1 Ω |
| I51-2 (2S) or I94-3 (2S) - Body ground | Always | 10 kΩ or higher |
| I51-2 (2S) - I3-12 (WHI) | Always | Below 1 Ω |
| I51-2 (2S) or I3-12 (WHI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I94 windshield wiper relay assembly connector.
Connect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I94)Location & Routingewd_type=routing;type=c;code=I94 |
||
| I94-3 (2S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for LHD)>REMOVAL
for RHD:
Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for RHD)>REMOVAL
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL