Home › Vehicle Exterior › LIGHTING (EXT) › SWITCH HOUSING
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468055 SWITCH HOUSING A

LIGHTING (EXT)  SWITCH HOUSING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E465448N01
5.906,2.896 6.417,2.896 false 1.594,1.906 1.594,2.406 false 5.24,1.188 4.677,1.188 false 3.104,0.885 3.104,1.323 false 6.521,2.781 6.802,3.135 0.281,0.354 18 false 1 1.521,2.427 1.802,2.781 0.281,0.354 18 false 3 5.667,1.042 5.948,1.396 0.281,0.354 18 false 2 3.031,0.552 3.313,0.906 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - - - -
2 WINDSHIELD WIPER SWITCH ASSEMBLY 84650 (Click here) - -
3 TURN SIGNAL SWITCH 84329 (Click here) - -
4 STEERING WHEEL SWITCH HOUSING 84319 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering wheel switch housing removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Steering angle setting Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 84650 2.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

Z101186

(Click here)

Hide 84329 3.REMOVE TURN SIGNAL SWITCH

Z101186

(Click here)

Hide 84319 4.REMOVE STEERING WHEEL SWITCH HOUSING

a.
E465450C01
0.594,0.042 0.875,0.396 0.281,0.354 18 true i 4.208,0.052 4.49,0.406 0.281,0.354 18 true ii
V113147

Remove in this Direction - -


i.

Using pliers, loosen and hold the plastic tie clamp.


ii.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the steering wheel switch housing as shown in the illustration.