Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2021.04–2022.11
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

The headlight ECU sub-assembly RH controls the headlight cleaner motor and pump assembly.

WIRING DIAGRAM

E467166E01
5.281,2.25 6.792,2.615 1.51,0.365 10 false Headlight Cleaner Motor and Pump Assembly 3.5,2.323 5.135,2.563 1.635,0.24 10 false Washer Wiring Assembly 3.219,1.74 3.552,1.927 0.333,0.188 10 false BB1 3.219,1.063 3.563,1.281 0.344,0.219 10 false BB1 4.979,1.063 5.292,1.271 0.313,0.208 10 false B53 4.979,1.74 5.302,1.969 0.323,0.229 10 false B53 0.75,0.417 1.448,0.604 0.698,0.188 10 false H-LP CLN 2.031,0.208 2.875,0.406 0.844,0.198 10 false from Battery 5.052,1.531 5.208,1.729 0.156,0.198 10 false 1 5.063,0.865 5.219,1.063 0.156,0.198 10 false 2 3.313,1.521 3.469,1.719 0.156,0.198 10 false 3 3.302,0.865 3.458,1.063 0.156,0.198 10 false 6 1.917,4.26 3.313,4.49 1.396,0.229 10 false from IGR NO.3 Relay 0.531,4.458 1.542,4.677 1.01,0.219 10 false ENG-IGR NO.3 2.479,5.438 3.542,5.656 1.063,0.219 10 false Steering Sensor 0.698,6.417 2.448,6.635 1.75,0.219 10 false : CAN Communication Line 4.969,6.115 6.26,6.479 1.292,0.365 10 false Headlight ECU Sub-assembly RH 4.958,5.938 5.417,6.135 0.458,0.198 10 false B7 5.094,5.51 5.458,5.708 0.365,0.198 10 false GND 4.781,5.406 5.094,5.604 0.313,0.198 10 false 12 5.073,3.938 5.396,4.146 0.323,0.208 10 false IGR 5.073,3.479 5.417,3.688 0.344,0.208 10 false HLC 0.583,2.177 2.156,2.635 1.573,0.458 10 false Headlight Cleaner Control Relay (H-LP CLN) 1.75,0.938 1.906,1.135 0.156,0.198 10 false 3 0.875,1.656 1.031,1.854 0.156,0.198 10 false 2 0.865,0.948 1.021,1.146 0.156,0.198 10 false 5 1.76,1.646 1.917,1.844 0.156,0.198 10 false 1 4.833,3.365 4.99,3.563 0.156,0.198 10 false 7 4.844,3.854 5,4.052 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

First check that the front washer operates normally.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>OPERATION CHECK

·

Check that the lighting system is normal before performing the following procedure.

w/ Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses and relays for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEADLIGHT CLEANER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Headlight Control (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Cleaner Operation Function to operate the headlight cleaner motor and pump assembly OFF or ON -
Body Electrical > Headlight Control (Sub) > Active Test
Tester Display
Headlight Cleaner Operation
50004 463 42002
OK:

Headlight cleaner motor and pump assembly operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT WINDOW WASHER SWITCH)

NG

3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
2.READ VALUE USING GTS (FRONT WINDOW WASHER SWITCH)
a.

Read the Data List according to the display on the GTS.

Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition
Washer Switch Windshield wiper switch assembly (washer switch) condition OFF or ON OFF: Windshield wiper switch assembly (washer switch) in OFF position
ON: Windshield wiper switch assembly (washer switch) in ON position
Chassis > Steering Angle Sensor > Data List
Tester Display
Washer Switch
50003 445 20
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

OK

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY (H-LPCLN)

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY (H-LPCLN)

OK

5.INSPECT WASHER WIRING ASSEMBLY

NG

REPLACE HEADLIGHT CLEANER CONTROL RELAY (H-LP CLN)

5.INSPECT WASHER WIRING ASSEMBLY
a.

Remove the washer wiring assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1,B53)Location & Routing

Click Connector(BB1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Washer Wiring Assembly

Click Connector(B53)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight Cleaner Motor and Pump Assembly

BB1-3 - B53-1 Always Below 1 Ω
BB1-6 - B53-2 Always Below 1 Ω
BB1-3 or B53-1 - Body ground Always 10 kΩ or higher
BB1-6 or B53-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY [H-LP CLN] AND BATTERY)

NG

REPLACE WASHER WIRING ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY [H-LP CLN] AND BATTERY)
a.

Disconnect the BB1 washer wiring assembly connector.


b.

Remove the headlight cleaner control relay (H-LP CLN) from the No. 1 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB1)Location & Routing

Click Connector(BB1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Washer Wiring Assembly

BB1-6 - Headlight cleaner control relay (H-LP CLN) terminal 3 Always Below 1 Ω
BB1-6 or Headlight cleaner control relay (H-LP CLN) terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY (H-LP CLN) - HEADLIGHT ECU SUB-ASSEMBLY RH, BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY (H-LP CLN) - HEADLIGHT ECU SUB-ASSEMBLY RH, BATTERY AND BODY GROUND)
a.

Remove the headlight cleaner control relay (H-LP CLN) from the No. 1 engine room relay block assembly.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

Headlight cleaner control relay (H-LP CLN) terminal 1 - B7-7 (HLC) Always Below 1 Ω
Headlight cleaner control relay (H-LP CLN) terminal 1 or B7-7 (HLC) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Headlight cleaner control relay (H-LP CLN) terminal 5 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR