Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU (for RHD)
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467816 NETWORK GATEWAY ECU(for RHD) A

NETWORKING  NETWORK GATEWAY ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E465048N03
4.76,0.625 4.76,0.406 4.76,0.406 5.125,0.406 false 5.25,2.281 5.25,2.531 5.25,2.531 5.417,2.531 false 2.146,2.833 2.146,3.271 false 6.417,1.958 6.417,2.25 6.417,2.25 6.583,2.25 false 0.927,0.896 1.156,0.896 1.156,0.896 1.156,1.146 false 2.198,0.854 2.417,0.854 2.417,0.854 2.417,1.271 false 2.094,3.302 2.375,3.656 0.281,0.354 18 false 1 5.688,2.469 5.969,2.823 0.281,0.354 18 false 2 6.844,2.146 7.125,2.5 0.281,0.354 18 false 2 5.208,0.281 5.49,0.635 0.281,0.354 18 false 3 0.688,0.75 0.969,1.104 0.281,0.354 18 false 4 1.99,0.719 2.271,1.073 0.281,0.354 18 false 5 5.469,1.073 5.927,1.271 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 73990 - - -
2 INSTRUMENT PANEL BOX DOOR COVER 55443A (Click here) - -
3 LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY 55320 - - -
4 ECU INTEGRATION BOX LH 82878 (Click here) - -
5 NETWORK GATEWAY ECU 89111 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the network gateway ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Central gateway ECU (network gateway ECU) Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:
ยท

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 73990 1.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55443A 2.REMOVE INSTRUMENT PANEL BOX DOOR COVER

Z101186

Click here(Click here)

Hide 55320 3.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 82878 4.REMOVE ECU INTEGRATION BOX LH

a.
E467158C01
4.135,0.125 4.271,0.406 0.135,0.281 18 true i 0.229,0.135 0.5,0.417 0.271,0.281 18 true ii 6.438,0.354 6.708,0.635 0.271,0.281 18 true iii
V113147

Remove in this Direction
V100135

Connector
V100136

Nut
V100137

Bolt


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


ii.

Disconnect the 4 connectors and detach the clamp.


iii.

Remove the bolt, nut and ECU integration box LH.



Hide 89111 5.REMOVE NETWORK GATEWAY ECU

a.
E464739C01
0.563,0.125 0.844,0.479 0.281,0.354 18 true i
V113147

Remove in this Direction - -


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the network gateway ECU.