Home › Vehicle Interior › HEATING / AIR CONDITIONING › PTC HEATER ASSEMBLY
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467912 PTC HEATER ASSEMBLY A

HEATING / AIR CONDITIONING  PTC HEATER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E465152N01
3.958,1.385 3.813,1.385 3.813,1.385 3.625,1.25 false 5.583,0.531 5.438,0.531 5.438,0.531 5.135,0.75 false 5.51,2.802 5.365,2.802 5.365,2.802 5.177,2.667 false 5.135,3.406 4.99,3.406 4.99,3.406 4.802,3.271 false 4.281,1.844 4.031,2.052 4.031,2.052 3.813,2.052 false 5.344,1.458 5.219,1.458 5.219,1.458 4.99,1.677 false 5.188,3.271 5.469,3.625 0.281,0.354 18 false 1 5.656,1.302 5.938,1.656 0.281,0.354 18 false 2 3.646,1.885 3.927,2.24 0.281,0.354 18 false 2 5.563,2.656 5.844,3.01 0.281,0.354 18 false 3 4.271,1.24 4.552,1.594 0.281,0.354 18 false 5 5.646,0.396 5.927,0.75 0.281,0.354 18 false 4 6.01,2.5 6.427,2.854 0.417,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 73990 - - -
2 INSTRUMENT PANEL BOX DOOR COVER 55443A (Click here) - -
3 LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY 55320 - - -
4 NO. 1 AIR DUCT SUB-ASSEMBLY 87201 - - -
5 QUICK HEATER ASSEMBLY 87710G (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the quick heater assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 73990 1.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55443A 2.REMOVE INSTRUMENT PANEL BOX DOOR COVER

Z101186

Click here(Click here)

Hide 55320 3.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 87201 4.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY

a.
E455146N01
3.385,1 3.688,1.271 0.302,0.271 10 false .


b.
E455147N01
4.292,0.76 4.615,1.083 0.323,0.323 10 false .


Hide 87710G 5.REMOVE QUICK HEATER ASSEMBLY

a.
E455148C01
1.448,0.677 1.594,0.948 0.146,0.271 18 true i 1.292,1.385 1.458,1.667 0.167,0.281 18 true ii 4.375,0.052 4.615,0.333 0.24,0.281 18 true iii
V113147

Remove in this Direction - -


i.

Disconnect the 2 connectors.


ii.

Remove the screw.


iii.

Detach the claw and remove the quick heater assembly as shown in the illustration.

NOTICE:
E382588C02
0.677,1.646 0.677,1 true 0.188,1.646 0.188,0.896 0.188,0.896 0.5,0.896 true 0.604,1.667 0.917,1.865 0.313,0.198 10 false *a 0.115,1.667 0.427,1.865 0.313,0.198 10 false *b
*a Element
*b Fin


·

Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.

·

Foul odors may occur due to oil adhering to the quick heater assembly.