| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B000111 | Driver Frontal Stage 1 Deployment Control Circuit Short to Ground | One of the following conditions is met:
·
The airbag ECU assembly detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
·
A spiral cable sub-assembly malfunction.
·
A horn button assembly malfunction.
·
An airbag ECU assembly malfunction. |
·
Wire harness
·
Spiral cable sub-assembly
·
Horn button assembly
·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Applicable |
When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B000111 is output | A |
| Past DTC B000111 is output | B |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Spiral Cable Sub-assembly |
| *4 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the spiral cable sub-assembly connector.
Disconnect the horn button assembly connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the connectors are not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Horn Button Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Spiral Cable Sub-assembly |
| *4 | Wire Harness |
| *5 | SST |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Light Green |
Connect the I24 airbag ECU assembly connector.
Connect the I25 spiral cable sub-assembly connector.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E (light green connector).
Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B000111 is not output | A |
| DTC B000111 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Disconnect SST from connector E.
A
B
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Spiral Cable Sub-assembly |
| *4 | Wire Harness |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Light Green |
Disconnect the I24 airbag ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(z8)Location & Routingewd_type=routing;type=c;code=z8 Click Connector(z8)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z8;pinno=2,1 |
||
| z8-2 - Body ground | Always | 1 MΩ or higher |
| z8-1 - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Horn Button Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Spiral Cable Sub-assembly |
| *4 | Wire Harness |
Connect the airbag ECU assembly connector.
Connect the horn button assembly connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B000111 is not output | A |
| DTC B000111 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Spiral Cable Sub-assembly |
| *4 | Wire Harness |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
Disconnect the spiral cable sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I25)Location & Routingewd_type=routing;type=c;code=I25 |
||
| I25-1 (D+) - Body ground | Always | 1 MΩ or higher |
| I25-2 (D-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG