Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B000112  Driver Frontal Stage 1 Deployment Control Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B000112 Driver Frontal Stage 1 Deployment Control Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A spiral cable sub-assembly malfunction.

·

A horn button assembly malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

E459588E24
5.208,0.396 5.313,0.542 0.104,0.146 10 false 6 5.208,1.219 5.313,1.365 0.104,0.146 10 false 7 3.073,0.396 3.177,0.542 0.104,0.146 10 false 1 3.073,1.219 3.177,1.365 0.104,0.146 10 false 2 1.99,1.198 2.094,1.344 0.104,0.146 10 false 1 1.99,0.375 2.094,0.521 0.104,0.146 10 false 2 5.448,0.479 5.781,0.646 0.333,0.167 10 false D+ 5.448,1.323 5.948,1.51 0.5,0.188 10 false D- 2.781,0.396 3.031,0.583 0.25,0.188 10 false D+ 2.802,1.219 3.094,1.417 0.292,0.198 10 false D- 5.208,1.719 5.583,1.906 0.375,0.188 10 false I24 0.365,1.688 0.708,1.854 0.344,0.167 10 false z8 1.969,1.719 3.292,2.073 1.323,0.354 10 false I25 0.354,1.854 1.865,2.125 1.51,0.271 10 false Horn Button Assembly 5.219,1.875 6.708,2.417 1.49,0.542 10 false Airbag ECU Assembly 1.979,1.906 3.115,2.26 1.135,0.354 10 false Spiral Cable Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B000112 is output A
Past DTC B000112 is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C371112C01
0.198,0.813 0.51,1.01 0.313,0.198 10 false *1 1.052,1.375 1.365,1.573 0.313,0.198 10 false *3 2.781,1.583 3.094,1.781 0.313,0.198 10 false *2 1.979,0.823 2.292,1.021 0.313,0.198 10 false *4
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.

Disconnect the horn button assembly connector.


Procedure1

d.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



e.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

g.

None



OK

4.CHECK HORN BUTTON ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HORN BUTTON ASSEMBLY
a.
C411565C07
0.417,2.156 0.75,2.385 0.333,0.229 1.448,2.729 1.688,2.938 1.688,2.938 1.833,2.938 true 1.74,2.229 1.875,2.115 1.875,2.115 2,2.115 true 0.229,0.885 0.625,1.188 0.396,0.302 10 false *1 2.729,1.271 3.177,1.656 0.448,0.385 10 false *2 1.115,1.01 1.563,1.365 0.448,0.354 10 false *3 0.333,1.688 0.729,2.177 0.396,0.49 10 false *a 1.906,2.865 2.219,3.021 0.313,0.156 10 false *b 2.052,2.031 2.531,2.448 0.479,0.417 10 false *5 0.51,2.177 0.875,2.479 0.365,0.302 10 false z8 2.344,0.615 2.792,0.969 0.448,0.354 10 false A 2.188,0.615 2.635,0.969 0.448,0.354 10 false B 1.76,0.615 2.208,0.969 0.448,0.354 10 false C 1.594,0.615 2.042,0.969 0.448,0.354 10 false D 0.75,0.615 1.198,0.969 0.448,0.354 10 false E 0.438,0.615 0.885,0.969 0.448,0.354 10 false F 1.927,0.448 2.406,0.865 0.479,0.417 10 false *4
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*5 SST
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Connect the I24 airbag ECU assembly connector.


b.

Connect the I25 spiral cable sub-assembly connector.


c.

Connect the white wire side of SST (resistance 2.1 Ω) to connector E (light green connector).

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK HORN BUTTON ASSEMBLY
5.CHECK HORN BUTTON ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B000112 is not output A
DTC B000112 is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Disconnect SST from connector E.



A

B

6.CHECK DRIVER SIDE AIRBAG SQUIB CIRCUIT
6.CHECK DRIVER SIDE AIRBAG SQUIB CIRCUIT

Pre-procedure1

a.
E441559C08
0.406,2.292 0.74,2.521 0.333,0.229 1.896,2.719 1.708,2.719 1.708,2.719 1.573,2.573 true 2.521,0.531 2.76,0.844 0.24,0.313 10 false A 2.208,0.542 2.448,0.854 0.24,0.313 10 false B 1.76,0.531 2,0.844 0.24,0.313 10 false C 1.604,0.531 1.844,0.844 0.24,0.313 10 false D 0.76,0.542 1,0.854 0.24,0.313 10 false E 0.448,0.542 0.688,0.854 0.24,0.313 10 false F 0.25,1.635 0.698,1.948 0.448,0.313 10 false *a 0.5,2.323 0.948,2.635 0.448,0.313 10 false z8 1.969,2.656 2.417,2.969 0.448,0.313 10 false *b 0.167,0.313 0.396,0.51 0.229,0.198 10 false *1 2.792,1.146 3.24,1.458 0.448,0.313 10 false *2 1.156,0.906 1.604,1.219 0.448,0.313 10 false *3 1.938,0.333 2.385,0.646 0.448,0.313 10 false *4
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Disconnect the I24 airbag ECU assembly connector.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z8)Location & Routing

Click Connector(z8)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

z8-2 - Body ground Ignition switch ON Below 1 V
z8-1 - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

7.CLEAR DTC

NG

9.CHECK HARNESS AND CONNECTOR
7.CLEAR DTC
a.
C371113C05
0.313,0.823 0.625,1.021 0.313,0.198 10 false *1 2.583,1.583 2.896,1.781 0.313,0.198 10 false *2 1.146,1.344 1.458,1.542 0.313,0.198 10 false *3 1.917,0.802 2.229,1 0.313,0.198 10 false *4
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the horn button assembly connector.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B000112 is not output A
DTC B000112 is output B



Post-procedure1

d.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B

9.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
C413909C16
0.406,2.26 0.823,2.51 0.417,0.25 0.896,2.948 1.021,2.948 1.021,2.948 1.167,2.594 true 1.729,2.979 1.594,2.979 1.594,2.979 1.417,2.594 true 0.24,0.802 0.552,1 0.313,0.198 10 false *1 1.99,0.76 2.302,0.958 0.313,0.198 10 false *4 2.802,1.125 3.115,1.323 0.313,0.198 10 false *2 1.094,0.896 1.406,1.094 0.313,0.198 10 false *3 0.354,1.646 0.667,1.844 0.313,0.198 10 false *a 0.667,2.885 1.021,3.073 0.354,0.188 10 false D+ 1.813,2.917 2.146,3.115 0.333,0.198 10 false D- 0.5,2.313 0.896,2.51 0.396,0.198 10 false I25 2.531,0.542 2.844,0.74 0.313,0.198 10 false A 2.26,0.552 2.573,0.75 0.313,0.198 10 false B 1.802,0.563 2.115,0.76 0.313,0.198 10 false C 1.531,0.552 1.844,0.75 0.313,0.198 10 false D 0.698,0.552 1.01,0.75 0.313,0.198 10 false E 0.458,0.542 0.771,0.74 0.313,0.198 10 false F
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I25)Location & Routing

Click Connector(I25)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

I25-1 (D+) - Body ground Ignition switch ON Below 1 V
I25-2 (D-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR