Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009887  Right Side Restraints Sensor 3 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009887 Right Side Restraints Sensor 3 Missing Message One of the following conditions is met:
·

The airbag ECU assembly detects a line short in the side collision sensor RH circuit (bus 1) for 2 seconds.

·

The airbag ECU assembly detects a short to ground in the side collision sensor RH circuit (bus 1) for 2 seconds.

·

The airbag ECU assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) for 2 seconds.

·

The airbag ECU assembly detects an open in the side collision sensor RH circuit (bus 1) for 2 seconds.

·

A No. 2 side airbag sensor assembly RH malfunction.

·

A side airbag pressure sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Side airbag pressure sensor RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C450171E31
1.594,0.677 1.75,0.875 0.156,0.198 10 false 2 1.583,1.479 1.74,1.677 0.156,0.198 10 false 1 2.854,0.656 3.01,0.854 0.156,0.198 10 false 1 2.844,1.479 3,1.677 0.156,0.198 10 false 2 4.146,0.667 4.302,0.865 0.156,0.198 10 false 4 5.333,0.656 5.646,0.854 0.313,0.198 10 false 26 5.365,1.479 5.677,1.677 0.313,0.198 10 false 25 4.177,1.49 4.333,1.688 0.156,0.198 10 false 3 5.635,0.792 6.25,0.99 0.615,0.198 10 false BBR+ 5.635,1.573 6.25,1.771 0.615,0.198 10 false BBR- 0.094,2.219 0.406,2.417 0.313,0.198 10 false M15 0.094,2.365 2.229,2.583 2.135,0.219 10 false Side Airbag Pressure Sensor RH 2.385,2.208 2.698,2.406 0.313,0.198 10 false Q2 2.385,2.375 5.25,2.698 2.865,0.323 10 false No. 2 Side Airbag Sensor Assembly RH 5.385,2.208 6,2.406 0.615,0.198 10 false Q1 5.385,2.365 6.854,2.677 1.469,0.313 10 false Airbag ECU Assembly 3.073,0.781 3.688,0.979 0.615,0.198 10 false BDR+ 3.083,1.573 3.698,1.771 0.615,0.198 10 false BDR- 3.615,0.781 4.229,0.979 0.615,0.198 10 false BCR+ 3.646,1.583 4.26,1.781 0.615,0.198 10 false BCR- 1.094,0.781 1.708,0.979 0.615,0.198 10 false BDR+ 1.083,1.604 1.698,1.802 0.615,0.198 10 false BDR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009887 and B009E87 are output A
DTC B009887 is output B
DTC B009887 and B009E87 are not output C



Post-procedure1

c.

None



A

2.CHECK SIDE AIRBAG PRESSURE SENSOR RH

B

C

2.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


b.

Disconnect the M15 side airbag pressure sensor RH connector.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

3.CHECK SIDE AIRBAG PRESSURE SENSOR RH
3.CHECK SIDE AIRBAG PRESSURE SENSOR RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009887 and B009E87 are output A
DTC B009E87 is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Connect the side airbag pressure sensor RH connector.



A

4.CHECK CONNECTION OF CONNECTORS

B

4.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

None


Procedure1

b.

Check that the connectors are properly connected to the airbag ECU assembly, No. 2 side airbag sensor assembly RH and side airbag pressure sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

5.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

5.CHECK CONNECTORS

Pre-procedure1

a.
C413757C01
0.604,1.458 0.917,1.615 0.313,0.156 10 false *1 2.573,1.469 2.885,1.625 0.313,0.156 10 false *2 1.521,1.094 1.833,1.25 0.313,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Pressure Sensor RH
*3 Wire Harness


Disconnect the Q2 No. 2 side airbag sensor assembly RH connector.


b.

Disconnect the M15 side airbag pressure sensor RH connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

Pre-procedure1

a.
E441556C11
0.719,0.865 1.135,1.115 0.417,0.25 0.813,3.448 1.229,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.698,1.031 true 2.354,1.583 2.104,1.583 2.104,1.583 1.865,1.031 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.917,3.49 1.229,3.646 0.313,0.156 10 false M15 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.833,0.906 1.146,1.063 0.313,0.156 10 false Q2 0.854,1.469 1.333,1.667 0.479,0.198 10 false BDR+ 2.417,1.49 2.979,1.75 0.563,0.26 10 false BDR- 0.875,2.927 1.438,3.188 0.563,0.26 10 false BDR- 2.438,2.917 3,3.177 0.563,0.26 10 false BDR+
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Pressure Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-1 (BDR+) - Q2-2 (BDR-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

Pre-procedure1

a.
E441556C11
0.719,0.865 1.135,1.115 0.417,0.25 0.813,3.448 1.229,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.698,1.031 true 2.354,1.583 2.104,1.583 2.104,1.583 1.865,1.031 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.917,3.49 1.229,3.646 0.313,0.156 10 false M15 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.833,0.906 1.146,1.063 0.313,0.156 10 false Q2 0.854,1.469 1.333,1.667 0.479,0.198 10 false BDR+ 2.417,1.49 2.979,1.75 0.563,0.26 10 false BDR- 0.875,2.927 1.438,3.188 0.563,0.26 10 false BDR- 2.438,2.917 3,3.177 0.563,0.26 10 false BDR+
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Pressure Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-1 (BDR+) - Body ground Always 1 MΩ or higher
Q2-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

8.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E441556C11
0.719,0.865 1.135,1.115 0.417,0.25 0.813,3.448 1.229,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.698,1.031 true 2.354,1.583 2.104,1.583 2.104,1.583 1.865,1.031 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.917,3.49 1.229,3.646 0.313,0.156 10 false M15 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.833,0.906 1.146,1.063 0.313,0.156 10 false Q2 0.854,1.469 1.333,1.667 0.479,0.198 10 false BDR+ 2.417,1.49 2.979,1.75 0.563,0.26 10 false BDR- 0.875,2.927 1.438,3.188 0.563,0.26 10 false BDR- 2.438,2.917 3,3.177 0.563,0.26 10 false BDR+
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Pressure Sensor RH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-1 (BDR+) - Body ground Ignition switch ON Below 1 V
Q2-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

9.CHECK CONNECTORS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTORS

Pre-procedure1

a.
E444958C01
0.385,1.688 0.698,1.885 0.313,0.198 10 false *1 2.771,1.479 3.083,1.677 0.313,0.198 10 false *2 1.458,1.375 1.771,1.573 0.313,0.198 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

10.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

Pre-procedure1

a.
E444955C04
1.26,3.667 1.677,3.917 0.417,0.25 0.198,0.833 0.615,1.083 0.417,0.25 1.646,4.448 1.896,4.448 1.896,4.448 1.99,4.073 true 2.438,4.479 2.188,4.479 2.188,4.479 2.094,4.073 true 1.042,1.49 1.292,1.49 1.292,1.49 1.427,1 true 1.99,1.51 1.74,1.51 1.74,1.51 1.583,1 true 0.417,2.885 0.604,3.052 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.021,2.417 1.208,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.385,2.417 2.573,2.583 0.188,0.167 10 false A 2.771,2.708 2.958,2.875 0.188,0.167 10 false *2 0.313,0.875 0.615,1.031 0.302,0.156 10 false Q2 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.667,1.396 1.177,1.573 0.51,0.177 10 false BCR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BCR+ 2.51,4.396 2.917,4.583 0.406,0.188 10 false BBR+ 1.292,4.385 1.677,4.542 0.385,0.156 10 false BBR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.542,2.604 1.771,2.76 0.229,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-4 (BCR+) - Q2-3 (BCR-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

11.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E444956C04
1.26,3.667 1.677,3.917 0.417,0.25 0.198,0.833 0.615,1.083 0.417,0.25 1.51,3.448 1.76,3.448 1.76,3.448 2,4.01 true 2.823,3.177 2.573,3.177 2.573,3.177 2.083,4.052 true 1.01,1.542 1.26,1.542 1.26,1.542 1.417,0.99 true 2.042,1.531 1.792,1.531 1.792,1.531 1.573,0.99 true 1.479,4.458 1.729,4.458 1.729,4.458 1.896,4.385 true 0.417,2.885 0.604,3.052 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.021,2.417 1.208,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.385,2.417 2.573,2.583 0.188,0.167 10 false A 2.771,2.708 2.958,2.875 0.188,0.167 10 false *2 0.302,0.885 0.604,1.042 0.302,0.156 10 false Q2 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.625,1.448 1.135,1.625 0.51,0.177 10 false BCR- 2.094,1.448 2.573,1.615 0.479,0.167 10 false BCR+ 2.865,3.115 3.271,3.302 0.406,0.188 10 false BBR+ 1.156,3.375 1.542,3.531 0.385,0.156 10 false BBR- 1.375,3.719 1.698,3.896 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.542,2.604 1.771,2.76 0.229,0.156 10 false *3 1.313,4.375 1.698,4.531 0.385,0.156 10 false *4
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 26 (BBR+) and 25 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-4 (BCR+) - Q2-3 (BCR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

12.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

Pre-procedure1

a.
E444955C04
1.26,3.667 1.677,3.917 0.417,0.25 0.198,0.833 0.615,1.083 0.417,0.25 1.646,4.448 1.896,4.448 1.896,4.448 1.99,4.073 true 2.438,4.479 2.188,4.479 2.188,4.479 2.094,4.073 true 1.042,1.49 1.292,1.49 1.292,1.49 1.427,1 true 1.99,1.51 1.74,1.51 1.74,1.51 1.583,1 true 0.417,2.885 0.604,3.052 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.021,2.417 1.208,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.385,2.417 2.573,2.583 0.188,0.167 10 false A 2.771,2.708 2.958,2.875 0.188,0.167 10 false *2 0.313,0.875 0.615,1.031 0.302,0.156 10 false Q2 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.667,1.396 1.177,1.573 0.51,0.177 10 false BCR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BCR+ 2.51,4.396 2.917,4.583 0.406,0.188 10 false BBR+ 1.292,4.385 1.677,4.542 0.385,0.156 10 false BBR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.542,2.604 1.771,2.76 0.229,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-4 (BCR+) - Body ground Always 1 MΩ or higher
Q2-3 (BCR-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E444955C04
1.26,3.667 1.677,3.917 0.417,0.25 0.198,0.833 0.615,1.083 0.417,0.25 1.646,4.448 1.896,4.448 1.896,4.448 1.99,4.073 true 2.438,4.479 2.188,4.479 2.188,4.479 2.094,4.073 true 1.042,1.49 1.292,1.49 1.292,1.49 1.427,1 true 1.99,1.51 1.74,1.51 1.74,1.51 1.583,1 true 0.417,2.885 0.604,3.052 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.021,2.417 1.208,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.385,2.417 2.573,2.583 0.188,0.167 10 false A 2.771,2.708 2.958,2.875 0.188,0.167 10 false *2 0.313,0.875 0.615,1.031 0.302,0.156 10 false Q2 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.667,1.396 1.177,1.573 0.51,0.177 10 false BCR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BCR+ 2.51,4.396 2.917,4.583 0.406,0.188 10 false BBR+ 1.292,4.385 1.677,4.542 0.385,0.156 10 false BBR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.542,2.604 1.771,2.76 0.229,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q2)Location & Routing

Click Connector(Q2)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 2 Side Airbag Sensor Assembly RH

Q2-4 (BCR+) - Body ground Ignition switch ON Below 1 V
Q2-3 (BCR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

14.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C374693C37
0.979,1.552 1.292,1.708 0.313,0.156 10 false *1 2.458,1.417 2.771,1.573 0.313,0.156 10 false *2 1.677,1.292 1.99,1.448 0.313,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the Q1 airbag ECU assembly connector.


b.

Connect the Q2 No. 2 side airbag sensor assembly RH connector.


c.

Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

15.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
15.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009887 and B009E87 are output A
DTC B009387 and B009B87 are output B


HINT:

Codes other than DTCs B009387, B009887, B009B87 and B009E87 may be output at this time, but they are not related to this check.



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

16.CHECK AIRBAG ECU ASSEMBLY

B

16.CHECK AIRBAG ECU ASSEMBLY
a.
C374693C37
0.979,1.552 1.292,1.708 0.313,0.156 10 false *1 2.458,1.417 2.771,1.573 0.313,0.156 10 false *2 1.677,1.292 1.99,1.448 0.313,0.156 10 false *3
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

17.CHECK AIRBAG ECU ASSEMBLY
17.CHECK AIRBAG ECU ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009887 and B009E87 are output A
DTC B0098887 and B009E87 are not output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



A

B