| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( ) |
- | - |
| 2 | DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL | - | ( ) |
- | - |
| 3 | REAR NO. 2 SEAT ASSEMBLY | - | - | - | - |
| 4 | TONNEAU COVER ASSEMBLY | 64910M | - | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/o Rear No. 2 Seat |
| *C | w/ Tonneau Cover | - | - |
| *A | w/o Rear No. 2 Seat | - | - |
| *A | for LH Side | *B | for RH Side |
| *C | w/ Rear No. 2 Seat | *D | w/ Tonneau Cover |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 2 side airbag sensor assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
|
|
for 1GR-FE:
for V35A-FTS:
3.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>REMOVAL
64910M 4.REMOVE TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat, w/ Tonneau Cover)
58410B 7.REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
58418H 8.REMOVE REAR FLOOR REAR BOARD LH (w/o Rear No. 2 Seat)
58417B 9.REMOVE REAR FLOOR REAR BOARD RH (w/o Rear No. 2 Seat)
Use the same procedure described for the LH side.
64993 10.REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58574G 11.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
67918D 12.REMOVE REAR DOOR SCUFF PLATE LH
73233D 13.REMOVE OUTER LAP BELT ANCHOR COVER
73370C 14.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73570 15.REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
62520B 17.REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for LH Side)
62510M 18.REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for RH Side)
89860C 19.REMOVE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY
| *a | Turns off | - | - |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Remove the bolt.
Loosen the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly guide is easily damaged.
If the No. 2 side airbag sensor assembly has been dropped, replace it with a new one.
Disengage the guide to remove the No. 2 side airbag sensor assembly.