| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B009B87 | Left Side Restraints Sensor 5 Missing Message | One of the following conditions is met:
·
A side airbag pressure sensor LH malfunction.
·
An airbag ECU assembly malfunction. |
·
Wire harness
·
Side airbag pressure sensor LH
·
No. 2 side airbag sensor assembly LH
·
Airbag ECU assembly |
Comes on | SRS Airbag | B | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B009387 and B009B87 are output | A |
| DTC B009B87 is output | B |
| DTC B009387 and B009B87 are not output | C |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the side airbag pressure sensor LH and rear airbag sensor LH.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Pressure Sensor LH |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Side Airbag Pressure Sensor LH) |
Disconnect the S2 No. 2 side airbag sensor assembly LH connector.
Disconnect the N13 side airbag pressure sensor LH connector.
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S2)Location & Routingewd_type=routing;type=c;code=S2 Click Connector(S2)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>No. 2 Side Airbag Sensor Assembly LHewd_type=component;type=c;code=S2;pinno=1,2 |
||
| S2-1 (BDL+) - S2-2 (BDL-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Disconnect the service wire from connector B.
OK
NG
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Wire Harness |
Connect the S2 No. 2 side airbag sensor assembly LH connector.
Interchange the side airbag pressure sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B009B87 is output | A |
| DTC B009E87 is output | B |
Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL