Home › Vehicle Interior › HEATING / AIR CONDITIONING › HEATER WATER PUMP
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467938 HEATER WATER PUMP A

HEATING / AIR CONDITIONING  HEATER WATER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E464330N01
0.76,4.104 1.01,4.104 1.01,4.104 1.146,3.74 false 2.073,4.104 1.875,4.104 1.875,4.104 1.771,3.74 false 4.25,5.208 4.542,5.458 4.542,5.458 4.938,5.458 false 1.26,0.5 1.521,0.25 1.521,0.25 1.917,0.25 false 6.281,0.323 6.74,0.323 false 1.042,2.74 1.365,2.74 false 0.385,1.375 0.635,1.375 0.635,1.375 0.771,1.667 false 2.083,4.729 2.198,4.583 2.198,4.583 2.354,4.583 false 2.792,5.271 2.885,5.125 2.885,5.125 3.042,5.125 false 3.656,5.313 4.115,5.51 0.458,0.198 10 false x 5 1.604,2.313 2.063,2.51 0.458,0.198 10 false x 2 1.375,1.333 1.833,1.531 0.458,0.198 10 false x 7 4.958,5.271 5.24,5.625 0.281,0.354 18 false 1 6.104,0.167 6.385,0.521 0.281,0.354 18 false 2 2.01,0.083 2.292,0.438 0.281,0.354 18 false 3 0.208,1.24 0.49,1.594 0.281,0.354 18 false 4 0.563,3.958 0.844,4.313 0.281,0.354 18 false 5 2.365,3.969 2.646,4.323 0.281,0.354 18 false 6 0.875,2.573 1.156,2.927 0.281,0.354 18 false 7 2.25,5.063 2.708,5.26 0.458,0.198 10 false x 2 2.688,5.448 3.146,5.646 0.458,0.198 10 false x 2 3.083,5.031 3.396,5.229 0.313,0.198 10 false *1 2.385,4.49 2.698,4.688 0.313,0.198 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 DRAIN ENGINE COOLANT - - (Click here) -
3 BATTERY 28800 - - -
4 BATTERY CARRIER ASSEMBLY 74410 - - -
5 OUTLET HEATER WATER HOSE B 87246B (Click here) - -
6 INLET HEATER WATER HOSE B 87245B (Click here) - -
7 HEATER ACCESSORY ASSEMBLY 87200D - - -

*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the heater accessory assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE COOLANT

Hide 28800 3.REMOVE BATTERY

Hide 74410 4.REMOVE BATTERY CARRIER ASSEMBLY

a.
E464331


Hide 87246B 5.DISCONNECT OUTLET HEATER WATER HOSE B

a.
E464332N01
1.313,0.104 1.594,0.458 0.281,0.354 18 false i

i.

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.





Hide 87245B 6.DISCONNECT INLET HEATER WATER HOSE B

a.
E464333N01
1.292,0.104 1.573,0.458 0.281,0.354 18 false i

i.

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.





Hide 87200D 7.REMOVE HEATER ACCESSORY ASSEMBLY

a.
E464334