An operation request signal is sent to the air conditioning amplifier assembly via LIN communication when the window defogger switch (air conditioning control assembly) is operated. When the air conditioning amplifier assembly receives the signal, it sends an operation request signal via CAN communication to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the signal, it sends an operation request signal via CPXI communication to the power distribution box assembly. After the operation request signal is received by the power distribution box assembly, it outputs an operation signal and operates the window defogger.
w/ Power Tilt and Power Telescopic Steering Column:
If the window defogger system is operated when the battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the windshield deicer system may not operate. In this case, check the vehicle control history (RoB) of the power steering system (w/ Variable Flow Control Solenoid Valve) and check that "Battery Voltage Drop: X21B6" is not stored before proceeding with troubleshooting.
With the negative (-) battery terminal connected, disconnect/do not connect the connector of the power distribution box assembly.
When replacing the power distribution box assembly, the system may not operate normally if the same part number is not used.
The window defogger system uses the CAN communication system, LIN communication system and CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the fuses for circuits related to this system before performing the following procedure.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Defogger Input Signal | Window defogger switch signal input condition | OFF/ON | OFF: Window defogger switch off ON: Window defogger switch on |
- |
| Tester Display |
|---|
| Rear Defogger Input Signal |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Defogger Output Signal | Window defogger output condition | OFF/ON | OFF: Window defogger does not operate ON: Window defogger operates |
- |
| Tester Display |
|---|
| Rear Defogger Output Signal |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Front view of wire harness connector (to Power Distribution Box Assembly) |
- | - |
Disconnect the power distribution box assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5J-1 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5B-44 - Body ground | Always | Below 1 Ω |
| 5C-25 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 5F power distribution box assembly connector.
Disconnect the Q41 radio setting condenser (noise filter) connector.
Disconnect the g19 back door glass (defogger wire) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g19)Location & Routingewd_type=routing;type=c;code=g19 Click Connector(g19)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Window Defogger (Back Door Glass)ewd_type=component;type=c;code=g19;pinno=1 |
||
| 5F-43 - g19-1 (B) | Always | Below 1 Ω |
| 5F-43 or g19-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the f4 back door glass (defogger wire) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(f4)Location & Routingewd_type=routing;type=c;code=f4 Click Connector(f4)Body>No. 1 Back Door Wire / No. 2 Rear Window Wire>Rear Window Defogger (Back Door Glass)ewd_type=component;type=c;code=f4;pinno=1 |
||
| f4-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER WIRE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the indicator illuminates when the defogger switch is on.
Defogger indicator illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Using the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Defogger Relay | RR DEF relay | OFF or ON | - |
| Tester Display |
|---|
| Rear Defogger Relay |
Back door glass (defogger wire) warms up.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
NG