When the windshield deicer switch on the air conditioning control assembly is operated, windshield deicer operation request signal is sent to the air conditioning amplifier assembly via LIN communication line.
When the air conditioning amplifier assembly receives windshield deicer operation request signal, it turns on the front wiper deicer relay (DEICER) to operate the windshield deicer system.
Inspect the fuses for circuits related to this system before performing the following procedure.
w/ Power Tilt and Power Telescopic Steering Column:
If the windshield deicer system is operated when the battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the windshield deicer system may not operate. In this case, check the vehicle control history (RoB) of the power steering system (w/ Variable Flow Control Solenoid Valve) and check that "Battery Voltage Drop: X21B6" is not stored before proceeding with troubleshooting.
Check air conditioning system.
Both the windshield deicer system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Front Deicer Relay | Windshield glass (windshield deicer) | OFF or ON |
| Tester Display |
|---|
| Front Deicer Relay |
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning control assembly with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Check that the windshield deicer system operates normally.
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B24*1 or B26*2 windshield glass (windshield deicer wire) connector.
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B24)Location & Routingewd_type=routing;type=c;code=B24 |
||
| B24-3 - Body ground | Ignition switch ON, windshield deicer switch off | Below 1 V |
| Ignition switch ON, windshield deicer switch on | 11 to 14 V | |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B26)Location & Routingewd_type=routing;type=c;code=B26 |
||
| B26-4 - Body ground | Ignition switch ON, windshield deicer switch off | Below 1 V |
| Ignition switch ON, windshield deicer switch on | 11 to 14 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B24*1 or B26*2 windshield glass (windshield deicer wire) connector.
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B24)Location & Routingewd_type=routing;type=c;code=B24 |
||
| B24-4 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B26)Location & Routingewd_type=routing;type=c;code=B26 |
||
| B26-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
| *a | Front view of wire harness connector (to Front Wiper Deicer Relay [DEICER]) |
Remove the front wiper deicer relay (DEICER) from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FRONT WIPER DEICER relay (DEICER) terminal 5 - Body ground | Always | 11 to 14 V |
| FRONT WIPER DEICER relay (DEICER) terminal 2 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front wiper deicer relay (DEICER) from the No. 1 engine room relay block.
Disconnect the B24 windshield glass (windshield deicer wire) connector.
Disconnect the I33 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B24,I33)Location & Routingewd_type=routing;type=c,c;code=B24,I33 |
||
| FRONT WIPER DEICER relay (DEICER) terminal 3 - B24-3 (B) | Always | Below 1 Ω |
| FRONT WIPER DEICER relay (DEICER) terminal 1 - I33-22 (FDEF) | Always | Below 1 Ω |
| FRONT WIPER DEICER relay (DEICER) terminal 3 or B24-3 (B) - Body ground | Always | 10 kΩ or higher |
| FRONT WIPER DEICER relay (DEICER) terminal 1 or I33-22 (FDEF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning control assembly with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Check that the windshield deicer system operates normally.
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG