| *A | w/ Winch | *B | w/o Winch |
| *C | for V35A-FTS | - | - |
|
Tightening torque for "major areas involving basic vehicle performance such as moving/turning/stopping" : N*m(kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | w/o Garnish | *B | w/ TOYOTA Parking Assist-sensor System |
| *C | w/ Headlight Cleaner System | *D | w/o TOYOTA Parking Assist-sensor System, w/o Fog Light |
| *E | w/ TOYOTA Parking Assist-sensor System or w/ Fog Light or w/ Both | *F | w/o Dynamic Radar Cruise Control System |
| *G | w/ Dynamic Radar Cruise Control System | - | - |
| *1 | FRONT BUMPER COVER | *2 | NO. 4 ENGINE ROOM WIRE |
| ● | Non-reusable part | - | - |
| *A | w/ Extension Mounting Bracket | *B | w/ Winch |
| *C | w/ Garnish | *D | w/o Garnish |
| *E | w/ TOYOTA Parking Assist-sensor System | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 41 | FOG LIGHT COVER LH | 81482C | - | - | - |
| 42 | FOG LIGHT COVER RH | 81481E | - | - | - |
| 43 | FRONT BUMPER HOLE COVER LH | 52128B | - | - | - |
| 44 | FRONT BUMPER HOLE COVER RH | 52127D | - | - | - |
| 45 | FOG LIGHT BRACKET LH | 81482M | - | - | - |
| 46 | FOG LIGHT BRACKET RH | 81481R | - | - | - |
| 47 | CORNERING LIGHT ASSEMBLY LH | - | - | - | - |
| 48 | CORNERING LIGHT ASSEMBLY RH | - | - | - | - |
| 49 | FOG LIGHT ASSEMBLY LH | - | - | - | - |
| 50 | FOG LIGHT ASSEMBLY RH | - | - | - | - |
| 51 | FRONT BUMPER INNER BRACKET LH | 52149H | - | - | - |
| 52 | FRONT BUMPER INNER BRACKET RH | 52149G | - | - | - |
| *A | w/o Fog Light | *B | w/ Fog Light |
| *C | w/o Cornering Light | *D | w/ Cornering Light |
| *A | w/ Headlight Cleaner System | *B | w/ TOYOTA Parking Assist-sensor System |
| *C | w/o Dynamic Radar Cruise Control System | *D | w/ Dynamic Radar Cruise Control System |
| *E | w/o Garnish | *F | w/ Panoramic View Monitor System |
| *1 | NO. 1 HEADLIGHT CLEANER CLAMP | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
52116A 1.INSTALL FRONT BUMPER SIDE SUPPORT LH
52115A 2.INSTALL FRONT BUMPER SIDE SUPPORT RH
52021 3.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Winch)
16550B 4.INSTALL NO. 2 INTERCOOLER COOLING RADIATOR ASSEMBLY (for V35A-FTS)
16550 5.INSTALL INTERCOOLER COOLING RADIATOR ASSEMBLY (for V35A-FTS)
165D1 6.INSTALL NO. 1 SUB-RADIATOR DUCT LH (for V35A-FTS)
165C1A 7.INSTALL NO. 1 SUB-RADIATOR DUCT RH (for V35A-FTS)
16595B 8.INSTALL NO. 1 RADIATOR AIR GUIDE LH (for V35A-FTS)
16593B 9.INSTALL NO. 1 RADIATOR AIR GUIDE RH (for V35A-FTS)
52618 10.INSTALL FRONT BUMPER LOWER ABSORBER (w/o Winch)
52521 11.INSTALL FRONT BUMPER CENTER UPPER RETAINER
52611 12.INSTALL FRONT BUMPER ENERGY ABSORBER (w/o Winch)
82090A 13.INSTALL EXTENSION WIRE ASSEMBLY (w/ Winch)
16595B 15.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Winch)
16593B 16.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Winch)
52421A 17.INSTALL FRONT BUMPER PAD
|
|
| Part | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
| Front Bumper Pad |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper pad and front bumper cover excessively.
| *a | Mark-off Line | - | - |
|
Installation area | - | - |
Clean the front bumper cover surface.
1. When reusing the front bumper cover, remove remaining double-sided tape from the front bumper cover.
2. Using a heat light, heat the front bumper cover surface.
3. Remove any remaining double-sided tape from the front bumper cover and wipe off any tape adhesive residue with cleaner.
4. Clean the installation area surface.
Installing the front bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new front bumper cover surface.
Using a heat light, heat the front bumper cover and a new front bumper pad.
Install the 4 front bumper pads in the position shown in the illustration.
The application strength of the front bumper pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front bumper cover.
53111 18.INSTALL RADIATOR GRILLE
85361C 20.INSTALL WASHER BRACKET (w/ Headlight Cleaner System)
Use the same procedure described for No. 2 washer bracket.
53113B 21.INSTALL RADIATOR SIDE GRILLE LH
53112B 22.INSTALL RADIATOR SIDE GRILLE RH
Use the same procedure described for LH side.
89C48E 23.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System, w/o Garnish)
53113C 24.INSTALL LOWER RADIATOR GRILLE LH (w/o Garnish)
53112C 25.INSTALL LOWER RADIATOR GRILLE RH (w/o Garnish)
53101 26.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
27.INSTALL NO. 7 RADIATOR GRILLE MOULDING (w/ TOYOTA Parking Assist-sensor System or w/Fog Light or w/ Both)
75310A 28.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY
53039 29.INSTALL UPPER RADIATOR SEAL
30.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
82114 31.INSTALL NO. 4 ENGINE ROOM WIRE
w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
w/ TOYOTA Parking Assist-sensor System or w/o Fog Light or w/ Both:
| *A | w/ Fog Light | *B | w/ Panoramic View Monitor System |
76878C 32.INSTALL FRONT SPOILER SIDE PROTECTOR LH (w/ Garnish)
|
|
| Part | Temperature |
|---|---|
| Front Bumper Guard Assembly | 20 to 30°C (68 to 86°F) |
| Front Spoiler Side Protector LH |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front spoiler side protector LH and front bumper guard assembly excessively.
| *a | Mark-off Line | *b | Cutout |
Clean the front bumper guard assembly surface.
1. When reusing the front bumper guard assembly, remove remaining double-sided tape from the front bumper guard assembly.
2. Using a heat light, heat the front bumper guard assembly surface.
3. Remove any remaining double-sided tape from the front bumper guard assembly and wipe off any tape adhesive residue with cleaner.
4. Clean the installation area surface.
Installing the front spoiler side protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new front bumper guard assembly surface.
Primer application.
1. Apply primer to the front bumper guard assembly on the installation area of the front spoiler side protector LH using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the front spoiler side protector LH has been attached.
2. Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Using a heat light, heat the front bumper guard assembly and a new front spoiler side protector LH.
Install the front spoiler side protector LH in the position shown in the illustration.
The application strength of the front spoiler side protector LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front bumper guard assembly.
76877E 33.INSTALL FRONT SPOILER SIDE PROTECTOR RH (w/ Garnish)
Use the same procedure described for LH side.
82223 34.INSTALL SWITCH WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Garnish)
89341L 35.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System, w/ Garnish)
52410B 36.INSTALL FRONT BUMPER GUARD ASSEMBLY (w/ Garnish)
C9715A 37.INSTALL NO. 1 WINCH WIRE (w/ Winch)
52049 38.INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY (w/ Winch)
75111 39.INSTALL FRONT LICENSE PLATE BRACKET (w/ Winch)
52114A 40.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Extension Mounting Bracket)
81482C 41.INSTALL FOG LIGHT COVER LH (w/ Fog Light)
81481E 42.INSTALL FOG LIGHT COVER RH (w/ Fog Light)
52128B 43.INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)
52127D 44.INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)
81482M 45.INSTALL FOG LIGHT BRACKET LH (w/ Fog Light)
81481R 46.INSTALL FOG LIGHT BRACKET RH (w/ Fog Light)
47.INSTALL CORNERING LIGHT ASSEMBLY LH (w/ Fog Light, w/ Cornering Light)
48.INSTALL CORNERING LIGHT ASSEMBLY RH (w/ Fog Light, w/ Cornering Light)
49.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light, w/o Cornering Light)
50.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light, w/o Cornering Light)
52149H 51.INSTALL FRONT BUMPER INNER BRACKET LH (w/ Fog Light)
52149G 52.INSTALL FRONT BUMPER INNER BRACKET RH (w/ Fog Light)
53.INSTALL COOLER THERMISTOR ASSEMBLY
86790B 54.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
88211B 55.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)
82824S 56.INSTALL WIRING HARNESS CONNECTOR (w/o Dynamic Radar Cruise Control System)
82667U 57.INSTALL NO. 32 CONNECTOR HOLDER (w/o Dynamic Radar Cruise Control System)
89C48D 58.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89341L 59.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System, w/o Garnish)
89341K 60.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
85208A 61.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A 62.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
85354 63.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)
85353 64.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)