Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468079 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B610516N01
3.5,1.125 3.75,1.125 3.75,1.125 3.833,1.458 false 5.104,0.365 5.521,0.365 false 5,1.75 5.5,1.75 false 4.344,1.479 4.51,1.479 false 2.156,1.021 2.323,0.688 2.323,0.688 2.573,0.688 false 5.99,0.177 6.271,0.531 0.281,0.354 18 false 1 5.844,0.229 6.125,0.583 0.281,0.354 10 false ● 5.958,1.604 6.24,1.958 0.281,0.354 18 false 2 5.833,1.646 6.115,2 0.281,0.354 10 false ● 4.188,1.354 4.469,1.708 0.281,0.354 18 false 4 2.677,0.563 2.958,0.917 0.281,0.354 18 false 3 3.292,1 3.573,1.354 0.281,0.354 18 false 5 4.615,1.365 5.073,1.563 0.458,0.198 10 false x 4 5,1.781 5.458,1.979 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD MOULDING SET CLIP 75532A (Click here) - -
2 NO. 3 WINDSHIELD MOULDING OUTSIDE CLIP 75547B (Click here) - -
3 WINDSHIELD GLASS 56111 - - -
4 NO. 1 WINDSHIELD MOULDING OUTSIDE CLIP 75545B - - -
5 WINDSHIELD MOULDING OUTSIDE LH 75534 - - -

● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75532A 1.INSTALL WINDSHIELD MOULDING SET CLIP

Z101186

NOTICE:

When installing a new windshield moulding set clip, heat the vehicle body and windshield moulding set clip using a heat light.


HINT:

Perform the following procedure only when replacement of the windshield moulding set clip is necessary.



Standard Value:
Part Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.
B609597C01
4.5,0.333 4.667,0.333 4.667,0.333 4.833,0.417 false 3.75,0.917 3.667,0.583 3.667,0.583 3.583,0.583 false 3.771,0.146 4.052,0.5 0.281,0.354 18 false i 5.667,0.146 5.948,0.5 0.281,0.354 18 false ii 3.75,1.49 4,1.75 0.25,0.26 18 true iii 3.406,0.5 3.719,0.698 0.313,0.198 10 false *b 4.323,0.25 4.635,0.448 0.313,0.198 10 false *a 4.646,2.5 4.802,2.698 0.156,0.198 10 false A 4.052,3.51 4.208,3.708 0.156,0.198 10 false B
*a Adhesive *b 2 to 3 mm (0.0787 to 0.1181 in.) Bead of Adhesive


Standard Measurement:
Area Measurement Area Measurement
A 0 to 2.0 mm (0 to 0.0787 in.) B 6.6 to 7.6 mm (0.260 to 0.299 in.)


i.

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new windshield moulding set clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



ii.

Apply primer to the body where the windshield moulding set clip will be installed.

NOTICE:

Do not let the primer dry.



iii.

While using the position shown in the illustration as a reference, place the windshield moulding set clip onto the roof panel. Then position and install the clip using the locations on the roof panel after lightly pressing it so that the adhesive adheres to the primer.

NOTICE:

Install the center roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the windshield moulding set clip.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours





Hide 75547B 2.INSTALL NO. 3 WINDSHIELD MOULDING OUTSIDE CLIP

a.
B610517N01
0.469,0.063 0.75,0.417 0.281,0.354 18 false i 2.042,0.063 2.323,0.417 0.281,0.354 18 false ii

i.

Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new No. 3 windshield outside moulding clip into the nose piece.


ii.

Press the No. 3 windshield outside moulding clips perpendicularly to the installation holes. Using the air riveter, install the 4 No. 3 windshield outside moulding clips.

NOTICE:
·

When installing the No. 3 windshield outside moulding clips to the panel surface, do not tilt the riveter.

·

Do not leave a gap between the No. 3 windshield outside moulding clip head portion and the panel.



HINT:

Pull the trigger again to cut off the No. 3 windshield outside moulding clip if it is not cut off.




Hide 56111 3.INSTALL WINDSHIELD GLASS

Hide 75545B 4.INSTALL NO. 1 WINDSHIELD MOULDING OUTSIDE CLIP

Hide 75534 5.INSTALL WINDSHIELD MOULDING OUTSIDE LH