Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0468065 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C458832C01
5.01,1.656 5.552,1.656 false 6.344,3.313 6.469,3.104 6.469,3.104 6.615,3.104 false 4.99,3.271 5.698,2.813 5.698,2.813 5.948,2.813 false 4.219,3.177 4.448,2.781 4.448,2.781 4.76,2.781 false 3.25,3.406 3.5,3.406 3.5,3.406 3.781,3.094 false 3.688,2.938 3.854,2.49 3.854,2.49 4.177,2.49 false 0.917,3.938 0.688,3.938 0.688,3.938 0.51,3.729 false 3.01,1.625 3.073,1.083 3.073,1.083 3.26,1.083 false 2.104,0.896 2.313,0.479 2.313,0.479 2.594,0.479 false 3.5,3.823 3.74,3.823 3.74,3.823 3.958,3.188 false 0.76,1.292 1.104,1.292 1.104,1.292 1.531,1.677 false 6.521,0.24 6.865,0.24 false 6.521,0.594 6.781,0.594 false 3.594,1.792 3.854,1.792 false 2,1.125 2.271,1.021 2.271,1.021 2.49,1.021 false 3.583,2.021 3.865,2.021 false 3.625,2.354 4.208,2.083 4.208,2.083 4.74,2.083 false 6.385,0.063 6.667,0.417 0.281,0.354 18 false 1 6.385,0.427 6.667,0.781 0.281,0.354 18 false 2 6.646,2.938 6.927,3.292 0.281,0.354 18 false 3 5.281,2.604 5.604,2.833 0.323,0.229 18 false 4 3.094,3.25 3.375,3.604 0.281,0.354 18 false 5 4.344,2.333 4.625,2.688 0.281,0.354 18 false 6 5.938,1.469 6.229,1.729 0.292,0.26 18 false 7 6.292,2.635 6.573,2.99 0.281,0.354 18 false 8 1.26,3.76 1.542,4.115 0.281,0.354 18 false 9 0.469,1.146 0.854,1.479 0.385,0.333 18 false 10 4.219,1.208 4.438,1.385 0.219,0.177 10 false x 2 3.573,0.917 3.958,1.24 0.385,0.323 18 false 11 3.385,3.719 3.542,3.917 0.156,0.198 10 false ● 2.646,0.406 2.802,0.604 0.156,0.198 10 false ● 5.125,2.677 5.344,2.875 0.219,0.198 10 false ● 1.594,2.677 1.906,2.875 0.313,0.198 10 false x 2 3.917,1.698 4.073,1.896 0.156,0.198 10 false ● 2.563,0.927 2.719,1.125 0.156,0.198 10 false ● 3.927,1.917 4.083,2.115 0.156,0.198 10 false ● 4.229,2.375 4.385,2.573 0.156,0.198 10 false ● 4.802,2.01 5.115,2.208 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 FRONT WHEEL - - - -
4 FRONT AXLE HUB GREASE CAP LH 43514C (Click here) - -
5 FRONT WHEEL ADJUSTING LOCK CAP LH 43525C - - -
6 FRONT AXLE SHAFT NUT LH 43502H - - -
7 FRONT DISC BRAKE CYLINDER ASSEMBLY LH 47750 (Click here) - -
8 FRONT DISC 43512 (Click here) - -
9 FRONT SPEED SENSOR LH 89543 (Click here) - -
10 TIE ROD END SUB-ASSEMBLY LH 45047 (Click here) - -
11 STEERING KNUCKLE LH 43212 (Click here) - -

*1 FRONT LH FLEXIBLE HOSE BRACKET
● Non-reusable part - -
V103638

Do not apply lubricants to the threaded parts

C458829C05
2.552,1.646 2.896,1.063 2.896,1.063 3.396,1.063 false 6.135,4.552 6.625,4.552 false 4.031,2.458 4.229,2.052 4.229,2.052 4.615,2.052 false 4.125,4.573 4.448,4.573 4.448,4.573 4.573,4.208 false 1.031,2.865 0.927,2.865 0.927,2.865 0.927,1.99 false 6.646,4.417 7.021,4.781 0.375,0.365 18 false 12 4.677,1.948 4.99,2.146 0.313,0.198 10 false *1 3.469,0.958 3.781,1.156 0.313,0.198 10 false *2 1.438,2.719 1.771,3.052 0.333,0.333 18 false 13 1.333,2.781 1.49,2.979 0.156,0.198 10 false ● 1.417,0.76 1.729,0.979 0.313,0.219 10 false x4 3.938,4.5 4.094,4.698 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

12 FRONT AXLE HUB SUB-ASSEMBLY LH 43502C - - -
13 FRONT AXLE HUB OIL SEAL LH 43502F (Click here) - -

*1 FRONT DISC BRAKE DUST COVER LH *2 STEERING KNUCKLE
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 43514C 4.REMOVE FRONT AXLE HUB GREASE CAP LH

a.
C458660C01
2.563,0.031 2.719,0.292 0.156,0.26 18 true i

i.

Using a screwdriver and hammer, remove the front axle hub grease cap LH.

NOTICE:

Do not damage the axle hub.




Hide 43525C 5.REMOVE FRONT WHEEL ADJUSTING LOCK CAP LH

a.
C458661C01
0,0 0,0 false


Hide 43502H 6.REMOVE FRONT AXLE SHAFT NUT LH

a.
C458662C01
0,0 0,0 false


Hide 47750 7.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY LH

a.
C456639C03
0.521,0.01 0.688,0.271 0.167,0.26 18 true i 4.375,0.021 4.615,0.313 0.24,0.292 18 true ii

i.

Remove the bolt and disconnect the front flexible hose from the steering knuckle LH.


ii.

Remove the 2 bolts and disconnect the front disc brake cylinder assembly LH from the steering knuckle LH.

NOTICE:
·

Do not disconnect the .from the front disc brake cylinder assembly LH.

·

Do not twist or bend the front flexible hose.





Hide 43512 8.REMOVE FRONT DISC

Z101186

Click here(Click here)

Hide 89543 9.DISCONNECT FRONT SPEED SENSOR LH

a.
C458974C01
2.188,2.021 2.427,2.302 0.24,0.281 18 true iii 3.896,0 4.135,0.271 0.24,0.271 18 true ii 0.531,0 0.719,0.25 0.188,0.25 18 true i

i.

Remove the 2 bolts and disconnect the speed sensor harness from the steering knuckle LH.

NOTICE:

If the upper arm is removed from the steering kunckle without disconnecting the speed sensor harness, the speed sensor is pulled along with the upper arm, resulting in damade to the speed sensor.



ii.

Remove the bolt, skid control sensor clamp and sensor wire.


iii.

Remove the bolt and disconnect the speed sensor from the knuckle.

NOTICE:

Pull out the sensor while trying as much as possible not to rotate it.




Hide 45047 10.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Z101186

Click here(Click here)

Hide 43212 11.REMOVE STEERING KNUCKLE LH

a.
C459032C01
2.094,2.729 2.25,2.427 2.25,2.427 2.469,2.427 true 0.5,0.063 0.719,0.385 0.219,0.323 18 false i 4.073,0.083 4.25,0.375 0.177,0.292 18 true ii 0.823,2.094 1.083,2.344 0.26,0.25 18 true iii 4.042,2.063 4.302,2.344 0.26,0.281 18 true iv 0.427,2.885 0.635,3.104 0.208,0.219 10 true *a 2.917,3.25 3.135,3.458 0.219,0.208 10 true *b 2.542,2.344 2.896,2.521 0.354,0.177 10 true SST
*a Hold *b Turn


i.

Support the front suspension lower arm LH with a jack.


ii.

Remove the clip and nut.


iii.

Using SST, disconnect the upper ball joint from the steering knuckle LH.

SST
09628-62011  

NOTICE:

Do not damage the ball joint dust cover.



iv.

Remove the 2 bolts and disconnect the lower ball joint attachment from the steering knuckle LH.



Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

Hide 43502F 13.REMOVE FRONT AXLE HUB OIL SEAL LH

a.
C456653C02
2.573,0.042 2.854,0.396 0.281,0.354 18 false i

i.

Using a screwdriver and hammer, tap out the front axle hub oil seal LH.

NOTICE:

Do not damage the steering knuckle.