Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD (for Instrument Panel)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0468130 RADIO ANTENNA CORD(for Instrument Panel) A

AUDIO / VIDEO  RADIO ANTENNA CORD(for Instrument Panel)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E462434N01
3.625,0.625 4.198,0.625 false 6.49,0.177 6.844,0.177 false 5.698,1.542 6.271,1.542 false 1.677,2.531 2.25,2.531 false 4.646,2.948 5.219,2.948 false 6.302,0.063 6.49,0.365 0.188,0.302 18 false 1 4.302,0.469 4.49,0.771 0.188,0.302 18 false 2 1.469,2.365 1.656,2.667 0.188,0.302 18 false 3 6.323,1.427 6.51,1.729 0.188,0.302 18 false 4 5.563,2.833 5.75,3.135 0.188,0.302 18 false 5 2.438,2.052 2.719,2.26 0.281,0.208 10 false x 3 4.427,1.708 4.708,1.917 0.281,0.208 10 false x 2 4.344,2.542 4.625,2.75 0.281,0.208 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 INSTRUMENT PANEL SAFETY PAD ASSEMBLY - - - -
3 DEFROSTER NOZZLE ASSEMBLY 55950G - - -
4 NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY 55086 - - -
5 NO. 2 SIDE DEFROSTER NOZZLE DUCT 55972C (Click here) - -

E462436N01
4.521,2.688 6.313,3.667 1.792,0.979 0.875,2.698 2.667,3.677 1.792,0.979 1.948,3.26 2.375,3.26 false 5.552,3.208 5.979,3.208 false 6.24,1.583 6.24,2.042 false 2.698,1.563 2.698,2.021 false 4.323,1.438 4.323,1.896 false 0.75,1.26 0.75,1.719 false 2.438,3.125 2.719,3.479 0.281,0.354 18 false 7 6.073,3.104 6.354,3.458 0.281,0.354 18 false 7 0.073,0.188 0.354,0.542 0.281,0.354 12 false *A 3.573,0.198 3.854,0.552 0.281,0.354 12 false *B 0.688,1.781 0.969,2.135 0.281,0.354 18 false 6 2.615,2.063 2.896,2.417 0.281,0.354 18 false 6 4.25,1.938 4.531,2.292 0.281,0.354 18 false 6 6.198,2.073 6.479,2.427 0.281,0.354 18 false 6 0.177,0.667 0.552,0.906 0.375,0.24 12 false *C 3.688,0.667 4.063,0.906 0.375,0.24 12 false *C 1.927,0.667 2.302,0.906 0.375,0.24 12 false *D 5.427,0.667 5.802,0.906 0.375,0.24 12 false *D 4.552,2.708 4.927,2.948 0.375,0.24 12 false *E 0.896,2.76 1.271,3 0.375,0.24 12 false *E

Procedure Part Name Code
Z101186

Z101188

Z101187

6 ANTENNA CORD SUB-ASSEMBLY 86101 - - -
7 NO. 1 NAVIGATION WIRE 86842 - - -

*A for LHD *B for RHD
*C for Type A *D for Type B
*E w/ Stereo Jack Adapter - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the antenna cord sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 55950G 3.REMOVE DEFROSTER NOZZLE ASSEMBLY

Hide 55086 4.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55972C 5.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Z101186

Click here(Click here)

Hide 86101 6.REMOVE ANTENNA CORD SUB-ASSEMBLY

HINT:

The illustrations are representative examples, and details may differ.


a.

for LHD:

E462438C01
0.073,0.063 0.344,0.281 0.271,0.219 12 false *A 3.927,0.073 4.229,0.313 0.302,0.24 12 false *B
*A for Type A *B for Type B



b.

for RHD:

E462439C01
0.052,0.063 0.354,0.25 0.302,0.188 12 false *A 3.656,0.083 3.938,0.292 0.281,0.208 12 false *B
*A for Type A *B for Type B



Hide 86842 7.REMOVE NO. 1 NAVIGATION WIRE (w/ Stereo Jack Adapter)

HINT:

The illustrations are representative examples, and details may differ.


a.
E462440C01
0.031,0.042 0.313,0.26 0.281,0.219 12 false *A 3.656,0.063 3.927,0.302 0.271,0.24 12 false *B
*A for LHD *B for RHD