| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent | ★ | Precoated part |
| *A | for LH Side | - | - |
| *1 | Wire Harness | *2 | Hole Plug |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP Grease | - | - |
| *A | w/ Courtesy Light | *B | w/ Reflex Reflector Assembly |
| *C | w/ Cover | - | - |
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
1.INSTALL HOLE PLUG
67837C 2.INSTALL REAR DOOR DUST PROOF SEAL
67858B 3.INSTALL REAR DOOR PANEL PROTECTOR
67923B 4.INSTALL REAR NO. 1 STIFFENER CUSHION
67898G 7.INSTALL REAR NO. 4 DOOR WEATHERSTRIP
75740 10.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67872 11.INSTALL REAR DOOR WEATHERSTRIP
Clean vehicle installation surface.
Engage the clips to install a new rear door weatherstrip.
Remove the release paper.
Press the double-side tape area of the rear door weatherstrip.
68640A 12.INSTALL REAR DOOR CHECK ASSEMBLY
| *A | When reusing the bolt | - | - |
|
Clean the thread |
|
Apply Adhesive 1324 |
Clean the bolt hole in the vehicle body.
When reusing the bolt:
1. Clean the threads of the bolt.
2. Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Install the rear door check assembly with the 2 nuts and bolt.
69204A 13.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
MP grease |
|
Install in this Direction |
Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.
Engage the clamp and install the wire harness.
Engage the guides.
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the "TORX" screw.
69242G 14.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
69241G 15.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
69227M 16.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claws.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the "TORX" screw.
69240 17.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
69032 19.INSTALL DOOR LOCK COVER SET
69804 21.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
|
MP grease | - | - |
Apply MP grease to the sliding parts on the rear door window regulator sub-assembly.
Temporarily install the rear door window regulator sub-assembly with the 6 nuts.
Fully tighten the 6 nuts to in the order shown in the illustration.
Connect the connector.
68189 22.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
68124C 23.INSTALL REAR DOOR QUARTER WINDOW GLASS
68104 24.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Connect the connector to the rear power window regulator switch assembly with rear door armrest base panel.
Connect the cable to negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Move the rear door window regulator assembly so that the door glass bolt holes can be seen.
|
Install in this Direction | - | - |
Turn the ignition switch off.
Disconnect the cable from negative (-) auxiliary battery terminal.
Disconnect the connector from the rear door power window regulator switch assembly with rear door armrest base panel.
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Do not damage the rear door glass sub-assembly.
Install the rear door glass sub-assembly with the 2 bolts.
67408E 25.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Temporarily install the rear door window division bar sub-assembly with bolts.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivet perpendicularly to the installation hole. Using the air riveter, install the rear door window division bar sub-assembly with the rivet.
When installing the rivet to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Fully tighten the 2 bolts to install the rear door window division bar sub-assembly.
67888F 26.INSTALL NO. 2 REAR DOOR WEATHERSTRIP
68152C 27.INSTALL REAR DOOR GLASS RUN
67842E 28.INSTALL REAR DOOR SERVICE HOLE COVER
68199 29.INSTALL REAR DOOR REAR BELT SEAL
68197A 30.INSTALL REAR DOOR FRONT BELT SEAL
68174A 31.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
67674A 32.INSTALL REAR DOOR FRAME GARNISH
69206C 33.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
67604 34.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
67812C 35.INSTALL REAR DOOR HOLE COVER (w/ Cover)
81580C 36.INSTALL REFLEX REFLECTOR ASSEMBLY (w/ Reflex Reflector Assembly)
81230 37.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
38.INSTALL REAR DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
67786D 39.INSTALL REAR DOOR TRIM UPPER COVER
40.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 1GR-FE:
for V35A-FTS:
41. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
42.INSPECT SRS WARNING LIGHT
43.INITIALIZE POWER WINDOW CONTROL SYSTEM
44.INSPECT POWER WINDOW CONTROL SYSTEM