Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0468588 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B608781N01
4.875,0.24 5.875,0.406 1,0.167 4.844,0.208 5.906,0.438 1.063,0.229 6.5,0.708 6.75,0.708 true 6.479,1.052 6.729,1.052 true 4.167,0.688 4.167,0.458 true 4.625,0.323 4.875,0.323 false 6.542,0.302 6.792,0.302 true 4.094,0.646 4.375,1 0.281,0.354 18 false 1 6.042,0.885 6.625,1.458 0.583,0.573 18 false 3, 5 6.354,0.542 6.635,0.896 0.281,0.354 18 false 2 6.396,0.146 6.958,0.438 0.563,0.292 18 false 4 4.927,0.25 6,0.417 1.073,0.167 8 false 9.0 (92, 80 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AIRBAG SENSOR LH 89174A (Click here) - -
2 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - (Click here) - -
3 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
4 CHECK SRS WARNING LIGHT - (Click here) - -
5 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR LH

a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B609499N01
0.406,0.052 0.688,0.406 0.281,0.354 18 false i 1.115,0 1.354,0.302 0.24,0.302 18 false 1 2.271,2.083 2.521,2.427 0.25,0.344 18 false 4 3.563,0 4.135,0.479 0.573,0.479 18 false 2, 3

i.

Perform the following procedure to install the front airbag sensor LH.

1. Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR


2. Engage the claw to hold the front airbag sensor LH in place.

NOTICE:
·

If the front airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the front airbag sensor LH, make sure that the wire harness does not interfere with or is not pinched between other parts.

·

Make sure that the front airbag sensor LH claw is securely inserted into the body hole.



3. Install the front airbag sensor LH with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the front airbag sensor LH because the front airbag sensor LH claw is easily damaged.


4. Check that there is no looseness in the installation parts of the front airbag sensor LH.



Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 3. PERFORM DIAGNOSTIC SYSTEM CHECK

Hide 5. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART