Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM38G0E _55 Steering _100923 STEERING COLUMN _0468603 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B261096  Tilt Position Sensor or Tilt Motor Circuit Component Internal Failure  


DESCRIPTION

The tilt motor (electric power steering column sub-assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor (electric power steering column sub-assembly) detects the tilt angle of the electric power steering column sub-assembly and sends a signal to the multiplex tilt and telescopic ECU based on that angle.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B261096 Tilt Position Sensor or Tilt Motor Circuit Component Internal Failure Tilt operation stops within the operation range while operating.
·

TI&TE Fuse

·

Tilt position sensor (electric power steering column sub-assembly)

·

Tilt motor (electric power steering column sub-assembly)

·

Harness or connector

·

Multiplex tilt and telescopic ECU


Tilt&Telescopic A

WIRING DIAGRAM

C244371E70
0.979,1.406 1.583,1.552 0.604,0.146 10 false Tilt Motor 2.125,0.781 2.99,1.198 0.865,0.417 10 false from Battery 3.531,0.979 4.073,1.271 0.542,0.292 10 false TI&TE 4.677,4.792 5.156,5.01 0.479,0.219 10 false I43 4.688,0.802 4.979,0.948 0.292,0.146 10 false +B 6.01,0.927 6.302,1.073 0.292,0.146 10 false +B 6.01,1.729 6.302,1.875 0.292,0.146 10 false +B 6.073,2.917 6.427,3.063 0.354,0.146 10 false 12 V 5.99,3.646 6.469,3.792 0.479,0.146 10 false to CPU 4.688,1.115 5.042,1.26 0.354,0.146 10 false TIM+ 4.688,2.656 5.042,2.802 0.354,0.146 10 false VCI 4.688,3.052 4.958,3.208 0.271,0.156 10 false TIS 4.688,3.844 5.25,4.042 0.563,0.198 10 false GND2 4.688,4.969 6.979,5.333 2.292,0.365 10 false Multiplex Tilt and Telescopic ECU 4.688,3.448 4.99,3.625 0.302,0.177 10 false E1 4.688,1.906 5.042,2.052 0.354,0.146 10 false TIM- 4.49,0.708 4.594,0.854 0.104,0.146 10 false 2 4.438,1.917 4.677,2.063 0.24,0.146 10 false 20 4.427,2.667 4.708,2.875 0.281,0.208 10 false 13 4.427,3.063 4.667,3.26 0.24,0.198 10 false 16 4.49,1.135 4.677,1.281 0.188,0.146 10 false 7 4.49,3.458 4.677,3.604 0.188,0.146 10 false 4 4.49,3.854 4.677,4 0.188,0.146 10 false 8 4.688,4.396 5.25,4.594 0.563,0.198 10 false GND 4.49,4.302 4.677,4.448 0.188,0.146 10 false 1 0.469,3.729 1.698,3.875 1.229,0.146 10 false Tilt Position Sensor 0.448,4.781 0.917,5.042 0.469,0.26 10 false I44 0.302,4.938 2.396,5.26 2.094,0.323 10 false Tilt Motor (Electric Power Steering Column Sub-assembly) 1.698,1.115 2.052,1.26 0.354,0.146 10 false TIM+ 2.115,1.917 2.333,2.188 0.219,0.271 10 false 2 1.719,1.917 2.073,2.063 0.354,0.146 10 false TIM- 2.125,1.125 2.292,1.375 0.167,0.25 10 false 1 1.781,2.656 2.073,2.802 0.292,0.146 10 false VCI 2.125,2.667 2.24,2.813 0.115,0.146 10 false 4 1.802,3.052 2.052,3.198 0.25,0.146 10 false TIS 2.125,3.063 2.24,3.208 0.115,0.146 10 false 5 1.823,3.438 2.021,3.583 0.198,0.146 10 false E1 2.125,3.448 2.24,3.594 0.115,0.146 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TILT MOTOR)
a.

Check that the steering wheel tilts up and down.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display
Tilt Motor
50004 406 42000
Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range
Tilt Motor Tilt operation UP/DOWN
OK:

The steering wheel tilts up and down.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY))

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY))
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Disconnect the I44 tilt motor (electric power steering column sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43,I44)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

Click Connector(I44)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Tilt Motor (Steering Column Assembly)

I43-13 (VCI) - I44-4 (VCI) Always Below 1 Ω
I43-16 (TIS) - I44-5 (TIS) Always Below 1 Ω
I43-4 (E1) -I44-6 (E1) Always Below 1 Ω
I43-13 (VCI) or I44-4 (VCI) - Body ground Always 10 kΩ or higher
I43-16 (TIS) or I44-5 (TIS) - Body ground Always 10 kΩ or higher
I43-4 (E1) or I44-6 (E1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-1 (GND) - Body ground Always Below 1 Ω
I43-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)
a.

Reconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Disconnect the I44 tilt motor (electric power steering column sub-assembly) connector.


c.
C401145C43
1.458,0.26 1.875,0.5 0.417,0.24 1.208,1.635 1.438,1.146 true 1.292,0.896 1.073,0.542 true 2.083,1.615 1.854,1.146 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false I43 0.979,0.385 1.438,0.583 0.458,0.198 10 false E1 1.01,1.667 1.469,1.865 0.458,0.198 10 false TIS 2.031,1.656 2.49,1.854 0.458,0.198 10 false VCI 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-13 (VCI) - I43-4 (E1) Ignition switch ON 8 to 14 V
I43-16 (TIS) - I43-4 (E1) Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK TILT POSITION SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TILT POSITION SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)
a.

Reconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Reconnect the I44 tilt motor (electric power steering column sub-assembly) connector.


c.
C287133C70
1.417,0.313 1.896,0.583 0.479,0.271 0.938,1.823 1.354,1.406 false 1.667,1.406 2.635,1.823 false 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.563,0.365 2.083,0.677 0.521,0.313 10 false I44 0.823,1.844 1.135,2.042 0.313,0.198 10 false E1 2.531,1.854 2.99,2.052 0.458,0.198 10 false TIS
*a Component with harness connected
(Tilt Motor (Electric Power Steering Column Sub-assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I44)Location & Routing

Click Connector(I44)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Tilt Motor (Steering Column Assembly)

I44-5 (TIS) - I44-6 (E1) Steering wheel tilting up or tilting down Pulse generation
High: 8 to 14 V
Low: Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-2 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-1 (GND) - Body ground Always Below 1 Ω
I43-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY))
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Disconnect the I44 tilt motor (electric power steering column sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43,I44)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

Click Connector(I44)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Tilt Motor (Steering Column Assembly)

I43-7 (TIM+) - I44-1 (TIM+) Always Below 1 Ω
I43-20 (TIM-) - I44-2 (TIM-) Always Below 1 Ω
I43-7 (TIM+) or I44-1 (TIM+) - Body ground Always 10 kΩ or higher
I43-20 (TIM-) or I44-2 (TIM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TILT MOTOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TILT MOTOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)

OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG