Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
RM38G0E _55 Steering _100923 STEERING COLUMN _0469199 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456075N01
5.427,2.104 5.844,2.104 true 6.521,0.25 6.854,0.25 true 5.938,0.115 6.646,0.448 0.708,0.333 18 false 1 - 3 5.938,1.979 6.292,2.344 0.354,0.365 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
3 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
4 STEERING WHEEL ASSEMBLY 45100 - - -

C456076N01
5,3.865 5.448,3.865 true 4.667,2.375 5.188,2.375 true 4.583,0.594 5.104,0.594 true 5.542,3.76 5.885,4.094 0.344,0.333 18 false 5 5.552,2.25 5.958,2.573 0.406,0.323 18 false 7 5.781,3.25 6.094,3.448 0.313,0.198 10 false x 3 5.188,0.469 5.542,0.771 0.354,0.302 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

5 LOWER STEERING COLUMN COVER SUB-ASSEMBLY 45024 - - -
6 UPPER STEERING COLUMN COVER 45286B - - -
7 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -

C456077N08
4.885,2.542 5.073,2.75 5.073,2.75 5.24,2.75 true 4.313,0.698 4.448,0.417 4.448,0.417 4.615,0.417 true 5.375,2.594 5.771,2.917 0.396,0.323 18 false 8 4.708,0.302 5.25,0.625 0.542,0.323 18 false 9 0.083,0.083 0.396,0.281 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

8 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
9 AIR DUCT SUB-ASSEMBLY - - - -

*A for LHD - -

C459448N05
4.885,2.542 5.073,2.75 5.073,2.75 5.24,2.75 true 3.115,0.813 3.25,0.531 3.25,0.531 3.417,0.531 true 5.375,2.594 5.771,2.917 0.396,0.323 18 false 8 3.5,0.396 4.042,0.719 0.542,0.323 18 false 9 0.083,0.083 0.396,0.281 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

8 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
9 AIR DUCT SUB-ASSEMBLY - - - -

*A for RHD - -

C456061N01
3.542,1.948 3.615,2.302 3.615,2.302 3.781,2.302 true 5.813,3.302 6,3.01 6,3.01 6.25,3.01 true 2.354,2.948 1.823,2.948 true 4.948,0.677 4.75,0.427 4.75,0.427 4.5,0.427 true 6.333,2.875 6.677,3.229 0.344,0.354 18 false 10 1.458,2.802 1.865,3.156 0.406,0.354 18 false 11 4.156,2.167 4.552,2.583 0.396,0.417 18 false 12 4.135,0.302 4.552,0.656 0.417,0.354 18 false 13 5.667,1.073 6.125,1.271 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

10 FRONT WHEEL LH - - - -
11 NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY 45203 (Click here) - -
12 STEERING INTERMEDIATE SHAFT ASSEMBLY 45220 (Click here) - -
13 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY 4520A - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor (Including removal and installation) Steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Steering angle setting Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Power steering ECU with motor assembly Assist map writing
·

DTCs are output

·

Power steering warning light illuminated


(Click here)
Update ECU security key Vehicle control history (Rob) are stored (Click here)
Electric power steering column sub-assembly Assist map writing There is a difference steering effort between turning left and right. (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

NOTICE:

Perform the customization settings before disconnecting the cable from the negative (-) auxiliary battery terminal. Otherwise, removal of the steering column cover becomes difficult.


HINT:

Record the customization settings before changing them.




b.

Move the steering wheel to its lowest and rearmost position.


Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

C456078

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 5.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C456079C01
0,0 0,0 false
V113146

Push Area
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)



Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C456063C03
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 7.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch to ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch to ON.

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data List, etc.), make sure to perform the inspection with the steering wheel assembly installed.




a.
C456080C01
1.021,3.792 1.188,3.792 true 0.698,1.25 1.083,0.917 1.083,0.917 1.25,0.917 true 0.865,3.708 1.177,3.906 0.313,0.198 10 false *b 0.188,2.927 0.51,3.344 0.323,0.417 18 false iii 3.698,2.938 4.021,3.354 0.323,0.417 18 false iv 0.542,0.115 1.135,0.479 0.594,0.365 18 false i, ii 1.302,0.813 1.615,1.01 0.313,0.198 10 false *a
*a Slider *b Clamp
V113147

Remove in this Direction - -


i.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


ii.

Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iii.

Using pliers, support the band clamp while loosened.


iv.

Detach the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the electric power steering column sub-assembly.



Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.REMOVE AIR DUCT SUB-ASSEMBLY

a.

for LHD:

C456081C01
0,0 0,0 false
V113147

Remove in this Direction - -



b.

for RHD:

C459461C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 10.REMOVE FRONT WHEEL LH

Hide 45203 11.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 45220 12.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C456719C01
4.594,1.177 5.51,1.333 5.51,1.333 4.594,1.458 true 1.865,0.302 2.052,0.135 2.052,0.135 1.875,0.417 true 5.552,1.229 5.813,1.469 0.26,0.24 10 true *a 2.125,0.042 2.385,0.281 0.26,0.24 10 true *a 0.417,0.063 0.938,0.438 0.521,0.375 18 true i, ii 3.865,0.052 4.479,0.385 0.615,0.333 18 true iii - v
*a Matchmark - -
V113147

Slide in this Direction - -


i.

Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not remove the steering intermediate shaft assembly from the electric power steering column sub-assembly.



ii.

Put matchmarks on the steering intermediate shaft assembly and electric power steering column sub-assembly.


iii.

Remove the steering intermediate shaft assembly from the electric power steering column sub-assembly.


iv.

Put matchmarks on the steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly.

HINT:

Perform this procedure only when replacement of the steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.



v.

Remove the steering intermediate shaft assembly from the No. 2 steering intermediate shaft assembly.

HINT:

Perform this procedure only when replacement of the steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.




Hide 4520A 13.REMOVE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

a.
C456082