The headlight ECU sub-assembly sends the automatic headlight beam leveling control signal to the headlight leveling motor via LIN communication. The headlight leveling motor operates according to the power supply and automatic headlight beam leveling control signals received from the headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly via LIN communication.
The headlight ECU sub-assembly sends the adaptive high beam system control signal to the light control LED ECU via LIN communication.
The light control LED ECU receives the power supply and control signals from the headlight ECU sub-assembly and controls the LED array and LED array fan, and sends its operating state to the headlight ECU sub-assembly via LIN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B244087 | AHS Driver LH Missing Message |
Detection condition:
The ignition switch is ON.
Malfunction status:
LIN communication is lost with light control LED ECU LH
Malfunction duration:
10 seconds or more |
·
Headlight unit assembly LH
·
Light control LED ECU LH
·
Headlight ECU sub-assembly LH |
Headlight Control | B |
| B244187 | AHS Driver RH Missing Message |
Detection condition:
The ignition switch is ON.
Malfunction status:
LIN communication is lost with light control LED ECU RH
Malfunction duration:
10 seconds or more |
·
Harness or connector
·
Headlight unit assembly RH
·
Light control LED ECU RH
·
Headlight ECU sub-assembly RH
·
Headlight ECU sub-assembly LH |
Headlight Control | B |
| Output DTC | Suspected Area (Malfunction Status) | |||
|---|---|---|---|---|
| B242487 | B242587 | B244087 | B244187 | |
|
○: DTC is output -: DTC is not output |
||||
| ○ | ○ | ○ | ○ | LIN communication circuit (short) |
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
| ○ | - | ○ | - | Headlight ECU sub-assembly LH (Internal malfunction) |
| - | ○ | - | ○ | LIN communication circuit (open) |
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
| ○ | - | - | - | Headlight leveling motor LH power supply system abnormal |
| Headlight leveling motor LH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly LH to headlight leveling motor LH) | ||||
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| - | ○ | - | - | Headlight leveling motor RH power supply abnormal |
| Headlight leveling motor RH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly RH to headlight leveling motor RH) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
| - | - | ○ | - | Light control LED ECU LH power supply system abnormal |
| Light control LED ECU LH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly LH to light control LED ECU LH) | ||||
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| - | - | - | ○ | Light control LED ECU RH power supply system abnormal |
| Light control LED ECU RH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly RH to light control LED ECU RH) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
If the DTCs are output simultaneously, the inspection area can be narrowed down.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>REGISTRATION
When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B242487, B242587, B244087 and B244187 are not output | A |
| B242487, B242587, B244087 and B244187 are output | B |
| B242487 and B244087 are output | |
| B242587 and B244187 are output | |
| B244087 is output | C |
| B244187 is output | D |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
Pre-procedure1
Remove the headlight unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected (to Light Control LED ECU LH) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-13 (LIN1_2) - D-13 (LIN) | Always | Below 1 Ω |
| C-1 (PSWH2+) - D-12 (ADD+) | Always | Below 1 Ω |
| C-2 (PSWH2-) - D-21 (ADD-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect all of the disconnected connectors.
Disconnect the light control LED ECU LH connector.
Procedure1
| *a | Component without harness connected (to Light Control LED ECU LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D-12 (ADD+) - D-21 (ADD-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the headlight unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected (to Light Control LED ECU RH) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-13 (LIN1_2) - D-13 (LIN) | Always | Below 1 Ω |
| C-1 (PSWH2+) - D-12 (ADD+) | Always | Below 1 Ω |
| C-2 (PSWH2-) - D-21 (ADD-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect all of the disconnected connectors.
Disconnect the light control LED ECU RH connector.
Procedure1
| *a | Component without harness connected (to Light Control LED ECU RH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D-12 (ADD+) - D-21 (ADD-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG