Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › 2021.04–2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  B242487  Leveling Motor LH Missing Message  B242587  Leveling Motor RH Missing Message  


DESCRIPTION

*: w/ Adaptive High Beam System


The headlight ECU sub-assembly sends the automatic headlight beam leveling control signal to the headlight leveling motor via LIN communication. The headlight leveling motor operates according to the power supply and automatic headlight beam leveling control signals received from the headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly via LIN communication.

The headlight ECU sub-assembly sends the adaptive high beam system control signal to the light control LED ECU via LIN communication.*

The light control LED ECU receives the power supply and control signals from the headlight ECU sub-assembly and controls the LED array and LED array fan, and sends its operating state to the headlight ECU sub-assembly via LIN communication.*

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242487 Leveling Motor LH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor LH


Malfunction duration:

10 seconds or more


·

Headlight unit assembly LH

·

Headlight leveling motor LH

·

Headlight ECU sub-assembly LH


Headlight Control A
B242587 Leveling Motor RH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor RH


Malfunction duration:

10 seconds or more


·

Harness or connector

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


Headlight Control A

w/ Adaptive High Beam System
Output DTC Suspected Area (Malfunction Status)
B242487 B242587 B244087 B244187

○: DTC is output

-: DTC is not output

○ ○ ○ ○ LIN communication circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
Headlight ECU sub-assembly RH (Internal malfunction)
○ - ○ - Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - ○ LIN communication circuit (open)
Headlight ECU sub-assembly RH (Internal malfunction)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - - - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - - Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
- - ○ - Light control LED ECU LH power supply system abnormal
Light control LED ECU LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to light control LED ECU LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- - - ○ Light control LED ECU RH power supply system abnormal
Light control LED ECU RH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly RH to light control LED ECU RH)
Headlight ECU sub-assembly RH (Internal malfunction)

w/o Adaptive High Beam System
Output DTC Suspected Area (Malfunction Status)
B242487 B242587

○: DTC is output

-: DTC is not output

○ ○ LIN communication circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
Headlight ECU sub-assembly RH (Internal malfunction)
○ - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
LIN communication circuit (open)
Harness open circuit (headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
Headlight ECU sub-assembly LH (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

w/ Adaptive High Beam System
E442330E09
1.625,0.74 2.177,0.948 0.552,0.208 10 false LIN I/F 0.948,2.323 1.563,2.521 0.615,0.198 10 false LINL 2.271,1.063 2.885,1.26 0.615,0.198 10 false LIN1_1 2.344,1.635 3.115,1.833 0.771,0.198 10 false ACTB 2.333,2.146 3.104,2.344 0.771,0.198 10 false ACTG 2,3.99 2.313,4.188 0.313,0.198 10 false IG 2,1.396 2.313,1.594 0.313,0.198 10 false IG 2.146,4.24 2.76,4.438 0.615,0.198 10 false PSWH2+ 0.594,2.49 1.052,2.688 0.458,0.198 10 false B4 0.615,2.292 0.927,2.49 0.313,0.198 10 false 20 2.906,1.26 3.063,1.458 0.156,0.198 10 false C 2.917,2.271 3.073,2.469 0.156,0.198 10 false B 2.917,1.76 3.073,1.958 0.156,0.198 10 false B 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.75 3.063,3.948 0.156,0.198 10 false C 2.917,4.365 3.073,4.563 0.156,0.198 10 false C 5.198,5.688 5.354,5.885 0.156,0.198 10 false D 5.531,3.75 5.99,3.948 0.458,0.198 10 false LIN 2.865,1.052 3.177,1.25 0.313,0.198 10 false 12 2.906,1.563 3.063,1.76 0.156,0.198 10 false 9 2.875,2.073 3.188,2.271 0.313,0.198 10 false 18 5.042,2.813 6.875,3.094 1.833,0.281 10 false Headlight Leveling Motor LH 2.875,3.552 3.104,3.76 0.229,0.208 10 false 13 2.917,4.167 3.073,4.365 0.156,0.198 10 false 1 2.927,4.771 3.083,4.969 0.156,0.198 10 false 2 5.229,3.583 5.615,3.823 0.385,0.24 10 false 13 5.229,4.25 5.594,4.521 0.365,0.271 10 false 12 5.25,4.854 5.438,5.042 0.188,0.188 10 false 21 5.51,4.375 6.219,4.646 0.708,0.271 10 false ADD+ 5.521,4.979 6.188,5.281 0.667,0.302 10 false ADD- 5.208,5.854 6.958,6.042 1.75,0.188 10 false Light Control LED ECU LH 3.969,6.521 6.573,6.719 2.604,0.198 10 false Headlight Unit Assembly LH 0.656,6.844 3.198,7.052 2.542,0.208 10 false Headlight ECU Sub-assembly LH 0.198,6.708 0.354,6.906 0.156,0.198 10 false A 0.813,7.458 2.625,7.677 1.813,0.219 10 false : LIN Communication Line 5.042,2.656 5.354,2.854 0.313,0.198 10 false F 5.292,1.083 5.448,1.281 0.156,0.198 10 false 3 5.302,1.635 5.458,1.833 0.156,0.198 10 false 1 5.313,2.146 5.469,2.344 0.156,0.198 10 false 4 2.25,3.563 2.865,3.76 0.615,0.198 10 false LIN1_2 2.177,4.813 2.792,5.01 0.615,0.198 10 false PSWH2-

w/ Adaptive High Beam System
E442331E09
0.188,0.188 0.542,0.479 0.354,0.292 10 false A 0.594,2.49 1.052,2.688 0.458,0.198 10 false B7 0.615,2.302 0.927,2.5 0.313,0.198 10 false 20 2.01,1.406 2.323,1.604 0.313,0.198 10 false IG 2,4.01 2.313,4.208 0.313,0.198 10 false IG 2.271,1.063 3.042,1.26 0.771,0.198 10 false LIN1_1 2.333,2.125 3.104,2.323 0.771,0.198 10 false ACTG 2.344,1.615 3.115,1.813 0.771,0.198 10 false ACTB 2.917,1.25 3.073,1.448 0.156,0.198 10 false C 2.927,2.271 3.083,2.469 0.156,0.198 10 false B 2.927,1.76 3.083,1.958 0.156,0.198 10 false B 2.875,1.042 3.188,1.24 0.313,0.198 10 false 12 2.927,1.563 3.083,1.76 0.156,0.198 10 false 9 2.885,2.063 3.198,2.26 0.313,0.198 10 false 18 5.115,2.656 5.271,2.854 0.156,0.198 10 false F 5.302,2.146 5.458,2.344 0.156,0.198 10 false 4 5.292,1.094 5.448,1.292 0.156,0.198 10 false 3 5.292,1.646 5.448,1.844 0.156,0.198 10 false 1 5.125,2.802 6.896,3.146 1.771,0.344 10 false Headlight Leveling Motor RH 2.25,3.563 3.021,3.76 0.771,0.198 10 false LIN1_2 2.146,4.26 2.76,4.458 0.615,0.198 10 false PSWH2+ 2.177,4.833 2.792,5.031 0.615,0.198 10 false PSWH2- 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.76 3.063,3.958 0.156,0.198 10 false C 2.906,4.385 3.063,4.583 0.156,0.198 10 false C 2.906,4.188 3.063,4.385 0.156,0.198 10 false 1 2.865,3.552 3.156,3.823 0.292,0.271 10 false 13 2.927,4.771 3.396,5.031 0.469,0.26 10 false 2 5.229,4.271 5.51,4.51 0.281,0.24 10 false 12 5.219,3.594 5.531,3.792 0.313,0.198 10 false 13 5.51,3.75 5.969,3.948 0.458,0.198 10 false LIN 5.25,4.854 5.563,5.052 0.313,0.198 10 false 21 5.521,4.365 6.052,4.594 0.531,0.229 10 false ADD+ 5.521,4.948 6.25,5.208 0.729,0.26 10 false ADD- 5.115,5.823 6.823,6.052 1.708,0.229 10 false Light Control LED ECU RH 3.875,6.521 6.479,6.719 2.604,0.198 10 false Headlight Unit Assembly RH 0.635,6.854 4.156,7.052 3.521,0.198 10 false Headlight ECU Sub-assembly RH 0.823,7.469 2.708,7.646 1.885,0.177 10 false : LIN Communication Line 0.927,2.333 1.26,2.51 0.333,0.177 10 false LINL 5.104,5.667 5.26,5.865 0.156,0.198 10 false D

w/o Adaptive High Beam System
E463613E02
5.073,6.76 6.99,7.281 1.917,0.521 10 false Headlight Leveling Motor RH 3.76,3.083 6.5,3.49 2.74,0.406 10 false Headlight Unit Assembly LH 3.823,7.25 6.563,7.656 2.74,0.406 10 false Headlight Unit Assembly RH 5.073,6.604 6.99,7.125 1.917,0.521 10 false F 2.875,5.083 4.792,5.604 1.917,0.521 10 false C 2.875,5.594 4.792,6.115 1.917,0.521 10 false B 2.875,6.104 4.792,6.625 1.917,0.521 10 false B 0.573,5.073 2.49,5.594 1.917,0.521 10 false B7 0.573,4.875 2.49,5.396 1.917,0.521 10 false 20 0.917,4.885 2.833,5.406 1.917,0.521 10 false LINL 0.938,0.813 2.854,1.333 1.917,0.521 10 false LINL 0.552,0.958 2.469,1.479 1.917,0.521 10 false B4 0.583,0.771 2.5,1.292 1.917,0.521 10 false 20 2.302,5.99 4.219,6.51 1.917,0.521 10 false ACTG 2.281,5.49 4.198,6.01 1.917,0.521 10 false ACTB 2.229,4.917 4.146,5.438 1.917,0.521 10 false LIN1_1 1.719,5.375 3.635,5.896 1.917,0.521 10 false IG 2.833,4.896 4.75,5.417 1.917,0.521 10 false 12 2.875,5.406 4.792,5.927 1.917,0.521 10 false 9 2.813,5.927 4.729,6.448 1.917,0.521 10 false 18 5.24,4.938 7.156,5.458 1.917,0.521 10 false 3 5.24,5.49 7.156,6.01 1.917,0.521 10 false 1 5.24,5.979 7.156,6.5 1.917,0.521 10 false 4 5.24,0.802 7.156,1.323 1.917,0.521 10 false 3 5.24,1.354 7.156,1.875 1.917,0.521 10 false 1 5.24,1.854 7.156,2.375 1.917,0.521 10 false 4 5.052,2.635 6.969,3.156 1.917,0.521 10 false Headlight Leveling Motor LH 5.063,2.469 6.979,2.99 1.917,0.521 10 false F 0.875,7.594 3.615,8 2.74,0.406 10 false Headlight ECU Sub-assembly RH 0.781,3.417 3.521,3.823 2.74,0.406 10 false Headlight ECU Sub-assembly LH 2.844,0.771 4.76,1.292 1.917,0.521 10 false 12 2.219,0.792 4.135,1.313 1.917,0.521 10 false LIN1_1 2.865,0.969 4.781,1.49 1.917,0.521 10 false C 2.26,1.365 4.177,1.885 1.917,0.521 10 false ACTB 2.875,1.281 4.792,1.802 1.917,0.521 10 false 9 2.885,1.469 4.802,1.99 1.917,0.521 10 false B 2.875,1.979 4.792,2.5 1.917,0.521 10 false B 2.24,1.906 4.156,2.427 1.917,0.521 10 false ACTG 1.771,1.271 3.688,1.792 1.917,0.521 10 false IG 2.823,1.802 4.74,2.323 1.917,0.521 10 false 18 0.823,8.313 3.563,8.719 2.74,0.406 10 false : LIN Communication Line 1.573,0.469 3.49,0.99 1.917,0.521 10 false LIN I/F

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
w/ Adaptive high beam system A
w/o Adaptive high beam system B



A

2.CLEAR DTC

B

31.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are not output A
B242487, B242587, B244087 and B244187 are output B
B242487 and B244087 are output C
B242587 and B244187 are output D
B242487 is output E
B242587 is output F
B244087 is output G
B244187 is output H



Post-procedure1

d.

None



A

B

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

D

19.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

E

27.INSPECT HEADLIGHT UNIT ASSEMBLY LH

F

29.INSPECT HEADLIGHT UNIT ASSEMBLY RH

G

H

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC

Pre-procedure1

a.

Connect the B4 No. 1 headlight ECU sub-assembly LH connector.


Procedure1

b.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

c.

None



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

7.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

16.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
7.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B4 headlight ECU sub-assembly LH connector.


c.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 and B244087 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

10.CHECK HEADLIGHT LEVELING MOTOR LH
10.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 is output B



Post-procedure1

d.

None



A

13.CHECK LIGHT CONTROL LED ECU LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

13.CHECK LIGHT CONTROL LED ECU LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU LH connector.


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244087 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE LIGHT CONTROL LED ECU LH

16.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

18.CHECK FOR DTC
18.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

21.CHECK HEADLIGHT LEVELING MOTOR RH
19.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

20.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E465495C01
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.167,2.083 6,2.083 6,2.083 5.854,1.479 true 5.406,2.094 5.573,2.094 5.573,2.094 5.75,1.479 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.271,0.333 2.583,0.531 0.313,0.198 10 false B7 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 4.917,2 5.458,2.229 0.542,0.229 10 false LIN1_2 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.25,2 6.792,2.229 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω
B7-20 (LINL) - C-13 (LIN1_2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

21.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

22.CLEAR DTC
22.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

23.CHECK FOR DTC
23.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 is output B



Post-procedure1

d.

None



A

24.CHECK LIGHT CONTROL LED ECU RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

24.CHECK LIGHT CONTROL LED ECU RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU RH connector.


Result:
Proceed to
NEXT



NEXT

25.CLEAR DTC
25.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

26.CHECK FOR DTC
26.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244187 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE LIGHT CONTROL LED ECU RH

27.INSPECT HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight unit assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

28.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

28.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

29.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

30.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

30.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

31.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

32.CHECK FOR DTC
32.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are not output A
B242487 and B24258 are output B
B242487 is output C
B242587 is output D



Post-procedure1

d.

None



A

B

33.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

C

27.INSPECT HEADLIGHT UNIT ASSEMBLY LH

D

48.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
33.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

34.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CLEAR DTC

Pre-procedure1

a.

Connect the B4 headlight ECU sub-assembly LH connector.


Procedure1

b.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

c.

None



NEXT

35.CHECK FOR DTC
35.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

36.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

42.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
36.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B4 headlight ECU sub-assembly LH connector.


c.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

37.CLEAR DTC
37.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

38.CHECK FOR DTC
38.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

39.CHECK HEADLIGHT LEVELING MOTOR LH
39.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

40.CLEAR DTC
40.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

41.CHECK FOR DTC
41.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

42.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

43.CLEAR DTC
43.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

44.CHECK FOR DTC
44.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

45.CHECK HEADLIGHT LEVELING MOTOR RH
45.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

46.CLEAR DTC
46.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

47.CHECK FOR DTC
47.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

48.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

49.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the C headlight unit assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

C-12 (LIN1_1) - B7-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

50.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

50.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Connect the B7 headlight ECU sub-assembly RH connector.


c.

Disconnect the C headlight unit assembly RH connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

C-12 (LIN1_1) - B4-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

51.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

51.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

52.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

52.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH