Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468606 ADAPTIVE HIGH BEAM SYSTEM J

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  Adaptive High Beam Switch Indicator does not Come ON  


DESCRIPTION

When the adaptive high beam system is on, the main body ECU (multiplex network body ECU) illuminates the auto high beam switch indicator.

WIRING DIAGRAM

E367187E51
3.385,1.5 4.885,1.698 1.5,0.198 10 false Auto High Beam Switch 3.073,1.49 3.333,1.677 0.26,0.188 10 false I81 3.104,0.948 3.469,1.125 0.365,0.177 10 false IND+ 2.927,0.948 3.292,1.125 0.365,0.177 10 false 3 4.604,0.948 5.031,1.156 0.427,0.208 10 false AZBI 5.01,0.938 5.375,1.115 0.365,0.177 10 false 4 5.823,0.938 6.25,1.146 0.427,0.208 10 false AHID 5.479,2.063 7.125,2.51 1.646,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 5.583,0.938 5.948,1.115 0.365,0.177 10 false 15 5.479,1.885 5.656,2.083 0.177,0.198 10 false I3 1.896,1.208 2.74,1.406 0.844,0.198 10 false ECU-B NO.3 0.615,1.01 1.427,1.229 0.813,0.219 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Switch Light Auto high beam switch indicator light OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Automatic High Beam Switch Light
50004 449 54
OK:

Auto high beam switch indicator light illuminates.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT AUTO HIGH BEAM SWITCH
2.INSPECT AUTO HIGH BEAM SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - BATTERY)
a.

Disconnect the I81 auto high beam switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I81)Location & Routing

Click Connector(I81)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Auto High Beam Switch

I81-3 (IND+) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I81 auto high beam switch connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR