Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468613 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives door key cylinder lock or unlock switch signals from the front door with motor lock assembly (for Driver Door). The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B494156E27
0.667,2.573 3.76,2.833 3.094,0.26 10 false Main Body ECU (Multiplex Network Body ECU) 0.677,2.417 1.271,2.708 0.594,0.292 10 false I3 4.365,2.302 5.781,2.594 1.417,0.292 10 false N2*1, *2, M2*3 4.365,2.479 6.552,2.854 2.188,0.375 10 false Front Door with Motor Lock Assembly (for Driver Door) 1.938,1.125 2.396,1.323 0.458,0.198 10 false L2 1.865,1.813 2.323,2.01 0.458,0.198 10 false UL3 4.75,1.125 5.208,1.323 0.458,0.198 10 false L 3.781,1.781 5.073,2.063 1.292,0.281 10 false 8*1, 10*2, 5*3 3.844,1.104 5.073,1.396 1.229,0.292 10 false 7*1, 9*2, 6*3 4.729,1.792 5.188,2.031 0.458,0.24 10 false UL 5.708,1.469 6.167,1.708 0.458,0.24 10 false E 5.906,1.469 6.938,1.792 1.031,0.323 10 false 9*1, 7*2, 8*3 2.188,1.115 2.646,1.354 0.458,0.24 10 false 28 2.188,1.792 2.646,2.031 0.458,0.24 10 false 4 1.167,0.875 1.625,1.073 0.458,0.198 10 false +B 1.167,1.542 1.625,1.74 0.458,0.198 10 false +B 0.271,2.885 3.5,3.167 3.229,0.281 10 false *1: for LHD (w/ Double Door Locking System) 0.271,3.167 3.5,3.448 3.229,0.281 10 false *2: for LHD (w/o Double Door Locking System) 0.271,3.458 3.5,3.74 3.229,0.281 10 false *3: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS (Door Lock Switch Status by a Mechanical Key (D/P Door), Door Unlock Switch Status by a Mechanical Key (D Door))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock Switch Status by a Mechanical Key (D/P Door) Driver door key-linked switch lock signal OFF or ON OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position
-
Door Unlock Switch Status by a Mechanical Key (D Door) Driver door key-linked switch unlock signal OFF or ON OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock Switch Status by a Mechanical Key (D/P Door)
Door Unlock Switch Status by a Mechanical Key (D Door)
50003 449 11,14
OK:

On the GTS screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)
2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the N2*1, *2 or M2*3 front door with motor lock assembly (for Driver Door) connector.

*1: for LHD (w/ Double Door Locking System)

*2: for LHD (w/o Double Door Locking System)

*3: for RHD



b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD (w/ Double Door Locking System):
Tester Connection Condition Specified Condition

Click Location & Routing(N2,I3)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

N2-7 (L) - I3-28 (L2) Always Below 1 Ω
N2-8 (UL) - I3-4 (UL3) Always Below 1 Ω
N2-9 (E) - Body ground Always Below 1 Ω
N2-7 (L) or I3-28 (L2) - Other terminals and body ground Always 10 kΩ or higher
N2-8 (UL) or I3-4 (UL3) - Other terminals and body ground Always 10 kΩ or higher

for LHD (w/o Double Door Locking System):
Tester Connection Condition Specified Condition

Click Location & Routing(N2,I3)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

N2-9 (L) - I3-28 (L2) Always Below 1 Ω
N2-10 (UL) - I3-4 (UL3) Always Below 1 Ω
N2-7 (E) - Body ground Always Below 1 Ω
N2-9 (L) or I3-28 (L2) - Other terminals and body ground Always 10 kΩ or higher
N2-10 (UL) or I3-4 (UL3) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(M2,I3)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

M2-6 (L) - I3-28 (L2) Always Below 1 Ω
M2-5 (UL) - I3-4 (UL3) Always Below 1 Ω
M2-8 (E) - Body ground Always Below 1 Ω
M2-6 (L) or I3-28 (L2) - Other terminals and body ground Always 10 kΩ or higher
M2-5 (UL) or I3-4 (UL3) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR