CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|
| A-13 (GND1) - Body ground | - | Ground | Always | Below 1 Ω | - |
| A-14 (GND2) - Body ground | - | Ground | Always | Below 1 Ω | - |
| A-26 (BECU) - Body ground | Input | Battery power supply | Always | 11 to 14 V | - |
| A-27 (IGR) - Body ground | Input | IG power supply | Ignition switch ON | 11 to 14 V | IGR Power |
| Ignition switch off | Below 1 V |
Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|
| 5E-7 (BZR) - Body ground | Output | Wireless door lock buzzer output | Active Test Wireless Buzzer on | Pulse generation (frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
- |
| Active Test Wireless Buzzer off | Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|
| I39-29 (E) - Body ground | - | Ground | Always | Below 1 Ω | - |
| I39-6 (+B) - Body ground | Input | Power supply | Always | 11 to 14 V | - |
Reconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|
| I38-21 (RCO) - I39-29 (E) | Output | Output to door control receiver (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Ignition switch off
2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 1) |
- |
| I38-11 (RDAM) - I39-29 (E) | Input | Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)). |
Proceed:
1.
Ignition switch off
2.
All doors locked
3.
Electrical key transmitter sub-assembly not inside vehicle
4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 2) |
- |
| I39-12 (CSEL) - I39-29 (E) | Output | Communication channel switching circuit | Procedure:
1.
Ignition switch off
2.
All doors closed |
Below 1 V → pulse generation | - |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I38-21 (RCO) - I39-29 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition |
Procedure:
1.
Ignition switch off
2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I38-11 (RDAM) - I39-29 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition |
Procedure:
1.
Ignition switch off
2.
All doors locked
3.
Electrical key transmitter sub-assembly not inside vehicle
4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |