In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function* does not operate. In such cases, hazard warning light and wireless door lock buzzer* signal output from the main body ECU (multiplex network body ECU) may be malfunctioning.
*: w/ Wireless Door Lock Buzzer Answer-back Function
Before performing the inspection, check that DTC B124296 (wireless door lock control) is not output.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Select the setting by referring to the table below.
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Wireless Buzzer Response Function | Function that enables/disables the wireless door lock buzzer response*1 | Enable | $00:Disable,$01:Enable | Main body ECU (Multiplex network body ECU) |
| Hazard Answer Back Function | Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation*2 | Enable | $00:Disable,$01:Enable | Main body ECU (Multiplex network body ECU) |
| Wireless Buzzer Volume Setting | Function that adjusts the wireless door lock buzzer volume*1 | Level5 | $00:Level7(MAX),$01:Level6,$02:Level5,$03:Level4,$04:Level3,$05:Level2,$06:Level1,$07:Level0(MIN) | Main body ECU (Multiplex network body ECU) |
*1: w/ Wireless Door Lock Buzzer Answer-back Function
*2: for the vehicle displaying the item "Hazard Answer Back Function" on the GTS.
| Result | Proceed to |
|---|---|
| All settings are Enable and other than Level0 | A |
| A setting is Disable or Level0 | B |
A
B
Check the wireless door lock control function using the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock operates properly. | A |
| Wireless door lock/unlock does not operate properly. | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Position Switch Status | Front door RH unlock detection switch signal | Lock or Unlock | Lock: Front door RH locked Unlock: Front door RH unlocked |
- |
| FL Door Lock Position Switch Status | Front door LH unlock detection switch signal | Lock or Unlock | Lock: Front door LH locked Unlock: Front door LH unlocked |
- |
| RR Door Lock Position Switch Status | Rear door RH unlock detection switch signal | Lock or Unlock | Lock: Rear door RH locked Unlock: Rear door RH unlocked |
- |
| RL Door Lock Position Switch Status | Rear door LH unlock detection switch signal | Lock or Unlock | Lock: Rear door LH locked Unlock: Rear door LH unlocked |
- |
| Tester Display |
|---|
| FR Door Lock Position Switch Status |
| FL Door Lock Position Switch Status |
| RR Door Lock Position Switch Status |
| RL Door Lock Position Switch Status |
The GTS display changes correctly in response to the lock/unlock operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur. (w/ Wireless Door Lock Buzzer Answer-back Function) | A |
| Only hazard warning light answer-back does not occur. | B |
A
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
Wireless door lock buzzer sounds
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the B35 wireless door lock buzzer connector.
Perform the Active Test using the GTS and sound the wireless door lock buzzer.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
While performing the Active Test, measure the voltage between the terminals of the wireless door lock buzzer.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B35)Location & Routingewd_type=routing;type=c;code=B35 |
||
| B35-1 (B) - B35-2 (E) | Active Test Wireless Buzzer ON | Pulse generation (frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
| Active Test Wireless Buzzer OFF | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B35 wireless door lock buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B35)Location & Routingewd_type=routing;type=c;code=B35 |
||
| B35-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B35 wireless door lock buzzer connector.
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the 5E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B35)Location & Routingewd_type=routing;type=c;code=B35 |
||
| B35-1 (B) - A-3 (BZR) | Always | Below 1 Ω |
| B35-1 (B) or A-3 (BZR) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 5E power distribution box assembly connector.
Disconnect the B35 wireless door lock buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B35)Location & Routingewd_type=routing;type=c;code=B35 |
||
| B35-1 (B) - 5E-7 | Always | Below 1 Ω |
| B35-1 (B) or 5E-7 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
w/ Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>Hazard Warning Switch Circuit
w/o Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>Hazard Warning Switch Circuit