Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467991 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


a.
B187998C20
0.958,0.208 1.375,0.469 0.417,0.26 1.927,0.208 2.344,0.469 0.417,0.26 2.042,0.26 2.333,0.448 0.292,0.188 10 false M4 1.458,0.25 1.771,0.448 0.313,0.198 10 false *A 1.083,0.26 1.375,0.417 0.292,0.156 10 false N3 2.427,0.25 2.74,0.448 0.313,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the N3*1 or M4*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-11 (B) - N3-12 (GND) Battery power supply Always 11 to 14 V
N3-12 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-11 (B) - M4-12 (GND) Battery power supply Always 11 to 14 V
M4-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N3*1 or M4*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-15 (DOWN) - N3-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
N3-20 (UP) - N3-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-15 (DOWN) - M4-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
M4-20 (UP) - M4-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V


e.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
N3-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
M4-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for LHD)


a.
B527906E32
1.5,0.156 1.938,0.438 0.438,0.281 1.625,0.208 2.083,0.406 0.458,0.198 10 false N5

Disconnect the N5 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
N5-1 (GND) - Body ground Ground Always Below 1 Ω
N5-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the N5 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N5-7 (DOWN) - N5-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
N5-10 (UP) - N5-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully opened 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N5-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for RHD)


a.
B527906E29
1.5,0.156 1.938,0.438 0.438,0.281 1.625,0.208 2.083,0.406 0.458,0.198 10 false N6

Disconnect the N6 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
N6-1 (GND) - Body ground Ground Always Below 1 Ω
N6-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the N6 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N6-7 (DOWN) - N6-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
N6-4 (AUTO) - N6-1 (GND) Power window motor AUTO UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
N6-10 (UP) - N6-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N6-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for LHD)


a.
B527906E33
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false M7

Disconnect the M7 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
M7-1 (GND) - Body ground Ground Always Below 1 Ω
M7-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the M7 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M7-4 (AUTO) - M7-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
M7-7 (DOWN) - M7-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
M7-10 (UP) - M7-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E2-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for RHD)


a.
B527906E24
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false M6

Disconnect the M6 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
M6-1 (GND) - Body ground Ground Always Below 1 Ω
M6-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the M6 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M6-7 (DOWN) - M6-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
M6-10 (UP) - M6-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M6-9 (LIN) - Body ground LIN communication line Ignition switch off Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


a.
B527906E25
1.5,0.156 1.938,0.438 0.438,0.281 1.625,0.219 2.083,0.417 0.458,0.198 10 false P4

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
P4-1 (GND) - Body ground Ground Always Below 1 Ω
P4-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the P4 rear power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
P4-4 (AUTO) - P4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
P4-7 (DOWN) - P4-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
P4-10 (UP) - P4-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
P4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B527906E26
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.219 2.094,0.417 0.458,0.198 10 false O4

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
O4-1 (GND) - Body ground Ground Always Below 1 Ω
O4-2 (B) - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the O4 rear power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O4-4 (AUTO) - O4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
O4-7 (DOWN) - O4-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
O4-10 (UP) - O4-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E448686C09
3.417,7.583 3.813,7.854 0.396,0.271 5.594,3.219 6.01,3.458 0.417,0.24 1.146,3.198 1.563,3.438 0.417,0.24 1.219,4.469 1.635,4.708 0.417,0.24 1.458,6.042 1.875,6.281 0.417,0.24 3.615,6.063 4.031,6.302 0.417,0.24 4.385,4.458 4.802,4.698 0.417,0.24 6.375,6.073 6.792,6.313 0.417,0.24 4.719,6.094 5.135,6.333 0.417,0.24 6.208,4.479 6.625,4.719 0.417,0.24 5.49,6.094 5.906,6.333 0.417,0.24 3.469,3.198 3.885,3.438 0.417,0.24 2.219,0.917 2.219,0.698 2.219,0.698 2.385,0.698 true 0.646,1.229 0.927,1.229 true 2.229,1.51 2.469,1.51 true 2.219,1.802 2.458,1.802 true 0.646,2.073 0.885,2.073 true 0.635,2.302 0.875,2.302 true 0.646,2.542 1.125,2.542 true 0.635,1.698 0.917,1.698 true 6.292,1.156 6.573,1.156 true 6.271,1.75 6.552,1.75 true 6.292,2.208 6.573,2.208 true 2.229,2.125 2.469,2.125 true 1.177,0.542 1.177,0.323 1.177,0.323 1.344,0.323 true 4.865,0.563 4.865,0.344 4.865,0.344 5.031,0.344 true 6.146,0.51 6.146,0.292 6.146,0.292 6.313,0.292 true 4.271,1.021 4.458,1.292 0.188,0.271 10 false A 3.573,7.625 3.865,7.813 0.292,0.188 10 false A 0.396,1.604 0.708,1.802 0.313,0.198 10 false 5E 0.396,1.99 0.708,2.188 0.313,0.198 10 false 5K 2.552,2.031 3.01,2.229 0.458,0.198 10 false I3 2.542,1.719 3,1.917 0.458,0.198 10 false I2 0.406,2.208 0.906,2.438 0.5,0.229 10 false 5J 2.479,0.594 2.938,0.792 0.458,0.198 10 false *2 6.656,1.073 6.969,1.271 0.313,0.198 10 false 5C 6.646,1.656 6.958,1.854 0.313,0.198 10 false 5B 1.292,3.24 1.75,3.438 0.458,0.198 10 false I3 3.635,3.229 4.094,3.427 0.458,0.198 10 false I2 1.354,4.51 1.667,4.708 0.313,0.198 10 false 5C 4.51,4.5 4.823,4.698 0.313,0.198 10 false 5B 1.583,6.073 1.896,6.271 0.313,0.198 10 false 5F 3.729,6.104 4.042,6.302 0.313,0.198 10 false 5E 6.49,6.115 6.802,6.313 0.313,0.198 10 false 5H 4.833,6.125 5.188,6.281 0.354,0.156 10 false 5K 0.406,1.135 1.021,1.333 0.615,0.198 10 false 5F 0.396,2.458 0.896,2.688 0.5,0.229 10 false 5H 6.656,2.115 6.969,2.313 0.313,0.198 10 false 5A 6.333,4.51 6.646,4.708 0.313,0.198 10 false 5A 5.625,6.125 5.938,6.323 0.313,0.198 10 false 5J 2.552,1.417 3.01,1.615 0.458,0.198 10 false I1 5.76,3.25 6.219,3.448 0.458,0.198 10 false I1 1.448,0.229 1.906,0.427 0.458,0.198 10 false *1 5.125,0.24 5.583,0.438 0.458,0.198 10 false *1 6.385,0.188 6.844,0.385 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-13 (GND1) - Body ground Ground Always Below 1 Ω
A-14 (GND2) - Body ground Ground Always Below 1 Ω
A-26 (BECU) - Body ground Battery power supply Always 11 to 14 V
A-27 (IGR) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION


e.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

5F-3 (FLCY) - Body ground*1 Courtesy light switch LH input Front door LH open Below 1 V
Front door LH closed 4.7 to 5.3 V
5F-5 (FRCY) - Body ground*2 Courtesy light switch RH input Front door RH open Below 1 V
Front door RH closed 4.7 to 5.3 V
I3-28 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
Driver door key cylinder off Pulse generation
I3-4 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
Driver door key cylinder off Pulse generation
5B-37 - Body ground LIN communication line Ignition switch ON Pulse generation
5F-17 - Body ground LIN communication line Ignition switch ON Pulse generation