CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| MB-14 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| MB-26 (BECU) - Body ground | Battery power supply | Always | 11 to 14 V |
| MB-27 (IGR) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU).
Measure the voltage and pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*1: w/ Footwell Light *2: w/ Courtesy Light |
|||
| 5H-1 - Body ground | DOME CUT relay drive power supply | Ignition switch off | 11 to 14 V |
| 5F-3 - Body ground | Front door courtesy light switch assembly (for LH) signal | Front door LH open | Below 1 V |
| Front door LH closed | 4.7 to 5.3 V | ||
| 5F-5 - Body ground | Front door courtesy light switch assembly (for RH) signal | Front door RH open | Below 1 V |
| Front door RH closed | 4.7 to 5.3 V | ||
| 5F-26 - Body ground | Rear door courtesy light switch assembly (for LH) signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 4.7 to 5.3 V | ||
| 5F-1 - Body ground | Rear door courtesy light switch assembly (for RH) signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 4.7 to 5.3 V | ||
| 5F-2 - Body ground | Back door lock assembly with courtesy light switch signal | Back door open | Below 1 V |
| Back door closed | 4.7 to 5.3 V | ||
| 5F-18 - Body ground | No. 1 luggage compartment light assembly ground | No. 1 luggage compartment light assembly off | 11 to 14 V |
| No. 1 luggage compartment light assembly on | Below 1 V | ||
| 5F-20 - Body ground | Interior light power supply | DOME CUT relay off | 11 to 14 V |
| DOME CUT relay on | Below 1 V | ||
| 5C-4 - Body ground | Interior light power supply | DOME CUT relay off | 11 to 14 V |
| DOME CUT relay on | Below 1 V | ||
| 5C-1 - Body ground | Each instrument panel illumination power supply | Light control switch in neither tail or head position | Below 1 V |
| Light control switch in tail or head position | 11 to 14 V | ||
| 5F-9 - Body ground | Each instrument panel illumination power supply | Light control switch in neither tail or head position | Below 1 V |
| Light control switch in tail or head position | 11 to 14 V | ||
| I3-5 (ILE) - Body ground | Illuminated entry system drive output | Illuminated entry system inactive | 11 to 14 V |
| Illuminated entry system operation | Below 1 V | ||
| 5B-28 - Body ground | Ambient illumination light power supply | Always | 11 to 14 V |
| 5C-18 - Body ground | Foot light ground*1 | Footwell light off | 11 to 14 V |
| Footwell light on | Below 1 V | ||
| 5C-22 - Body ground | Foot light ground*1 | Footwell light off | 11 to 14 V |
| Footwell light on | Below 1 V | ||
| I2-14 (LED2) - Body ground | Inside handle illumination light ground*1 | Inside handle illumination light off | 11 to 14 V |
| Inside handle illumination light on | Below 1 V | ||
| I2-19 (FLCL) - Body ground | Front door courtesy light LH ground*2 | Front door courtesy light LH off | 11 to 14 V |
| Front door courtesy light LH on | Below 1 V | ||
| I2-18 (FRCL) - Body ground | Front door courtesy light RH ground*2 | Front door courtesy light RH off | 11 to 14 V |
| Front door courtesy light RH on | Below 1 V | ||
| I2-5 (LCYL) - Body ground | Rear door courtesy light LH ground*2 | Rear door courtesy light LH off | 11 to 14 V |
| Rear door courtesy light LH on | Below 1 V | ||
| I2-22 (RCYL) - Body ground | Rear door courtesy light RH ground*2 | Rear door courtesy light RH off | 11 to 14 V |
| Rear door courtesy light RH on | Below 1 V | ||
| I3-9 (LSFL) - Body ground | Front door unlock detection switch LH input | Front door LH locked | Pulse generation |
| Front door LH unlocked | Below 1 V | ||
| I3-3 (LSFR) - Body ground | Front door unlock detection switch RH input | Front door RH locked | Pulse generation |
| Front door RH unlocked | Below 1 V | ||
| I3-10 (LSWL) - Body ground | Rear door unlock detection switch LH input | Rear door LH locked | Pulse generation |
| Rear door LH unlocked | Below 1 V | ||
| I2-23 (LSWR) - Body ground | Rear door unlock detection switch RH input | Rear door RH locked | Pulse generation |
| Rear door RH unlocked | Below 1 V | ||
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I39-6 (+B) - Body ground | Battery power supply | Always | 11 to 14 V |
| I39-29 (E) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I39-20 (SWIL) - I39-30 (AGND) | Engine switch illumination drive output | Engine switch illumination on | 11 to 14 V |
| Engine switch illumination off | Below 1 V |