The main body ECU (multiplex network body ECU) controls the rear fog lights.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the light control switch to the tail position.
Turn the rear fog light switch on.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Input Signal | Rear fog light input | OFF or ON | OFF: Rear fog lights off ON: Rear fog lights on |
- |
| Tester Display |
|---|
| Rear Fog Light Input Signal |
Display changes according to the rear fog light switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the g2 rear light socket and wire LH connector.
Disconnect the g1 rear light socket and wire RH connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g1,g2)Location & Routingewd_type=routing;type=c,c;code=g1,g2 Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=g1;pinno=7 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=7 |
||
| g1-7 (B) - 5F-7 | Always | Below 1 Ω |
| g2-7 (B) - 5F-7 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the A rear light assembly LH connector.
Turn the light control switch to the tail position.
Turn the rear fog light switch on.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g2 rear light socket and wire LH connector.
Turn the light control switch to the tail position.
Turn the rear fog light switch on.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A rear light assembly RH connector.
Turn the light control switch to the tail position.
Turn the rear fog light switch on.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g1 rear light socket and wire RH connector.
Turn the light control switch to the tail position.
Turn the rear fog light switch on.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Rear Fog Light Fuse Shut Off Status | Rear fog light fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Rear Fog Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g2 rear light socket and wire LH connector.
Disconnect the g1 rear light socket and wire RH connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g2,g1)Location & Routingewd_type=routing;type=c,c;code=g2,g1 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=7 Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=g1;pinno=7 |
||
| g2-7 (B) or 5F-7 - Body ground | Always | 10 kΩ or higher |
| g1-7 (B) or 5F-7 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG