Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468743 AUTOMATIC TRANSMISSION SYSTEM C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P271313  Pressure Control Solenoid "D" Circuit Open  


DESCRIPTION

Refer to the description for DTC P27137F

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>P27137F

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P271313 Pressure Control Solenoid "D" Circuit Open Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM


Comes on DTC stored SAE Code:
P2716

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

5.

Input the DTC: P271313.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C351511E86
1.51,1.708 5.177,1.906 3.667,0.198 10 false Shift Solenoid Valve SLT 1.083,1.302 1.24,1.5 0.156,0.198 10 false 1 1.083,2.115 1.24,2.313 0.156,0.198 10 false 2 3.469,1.104 4.083,1.302 0.615,0.198 10 false SLT+ 3.479,2.073 4.094,2.271 0.615,0.198 10 false SLT- 3.917,1.104 4.229,1.302 0.313,0.198 10 false 13 3.906,2.083 4.219,2.281 0.313,0.198 10 false 14 4.865,1.115 5.094,1.313 0.229,0.198 10 false 10 4.948,2.073 5.198,2.26 0.25,0.188 10 false 9 5.177,1.115 5.792,1.313 0.615,0.198 10 false SLT+ 5.198,2.073 5.813,2.271 0.615,0.198 10 false SLT- 1.49,2.667 1.948,2.865 0.458,0.198 10 false C89 1.49,2.865 4.094,3.063 2.604,0.198 10 false Transmission Wire 5.604,3.01 6.063,3.208 0.458,0.198 10 false C92 5.604,3.188 6.063,3.385 0.458,0.198 10 false ECM 5.802,0.781 6.417,0.979 0.615,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C319326C59
1.406,0.115 1.823,0.427 0.417,0.313 1.813,1.729 1.969,1.177 true 2.448,1.74 2.188,1.177 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.677,1.792 2.146,1.99 0.469,0.198 10 false SLT- 2.281,1.802 2.698,1.99 0.417,0.188 10 false SLT+ 1.49,0.177 1.948,0.375 0.458,0.198 10 false C89
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C89)Location & Routing

Click Connector(C89)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

C89-13 (SLT+) - C89-14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C89-13 (SLT+) - Body ground Always 10 kΩ or higher
C89-14 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C92)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C92-10 (SLT+) - C92-9 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C92-10 (SLT+) - Body ground Always 10 kΩ or higher
C92-9 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG