These DTCs are stored when a malfunction occurs in the roof antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C0 | GPS Antenna Connection Malfunction(short) | Navigation antenna malfunction |
·
Navigation antenna assembly
·
Antenna cord sub-assembly
·
Navigation ECU assembly
·
Radio and display receiver assembly
·
Telephone antenna assembly*1
·
No. 3 antenna cord sub-assembly*2
·
Antenna divider |
Navigation System | A |
| B15C1 | GPS Antenna Connection Malfunction(break) | Navigation antenna power source malfunction |
·
Navigation antenna assembly*3
·
Antenna cord sub-assembly
·
Navigation ECU assembly
·
Radio and display receiver assembly
·
Telephone antenna assembly*1
·
No. 3 antenna cord sub-assembly*1
·
Antenna divider*2 |
Navigation System | A |
*1: w/ Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System and w/ Telematics Transceiver
*3: w/o Heated Windshield Defroster System
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Pre-procedure1
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Heated Windshield Defroster System | A |
| w/ Heated Windshield Defroster System | B |
A
B
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *a | Front view of wire harness connector (to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector (to Navigation ECU Assembly) |
Disconnect the antenna connector from the navigation antenna assembly.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-1 (GPS) | Always | Below 1 Ω |
| A-3a - B-1a | Always | Below 1 Ω |
| A-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Replace the navigation ECU assembly with a known good one.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Pre-procedure1
Disconnect the antenna connector from the roof antenna assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Procedure1
| *a | Front view of antenna connector (to Roof Antenna Assembly) |
| *b | Front view of antenna connector (to Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-2 | Always | Below 1 Ω |
| A-2a - B-2a | Always | Below 1 Ω |
| A-2 or B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Telematics Transceiver | A |
| w/ Telematics Transceiver | B |
A
B
Pre-procedure1
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
| *a | Front view of antenna connector (to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of antenna connector (to Navigation ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - C-2 (GPS1) | Always | Below 1 Ω |
| B-2a - C-2a | Always | Below 1 Ω |
| B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Pre-procedure1
Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
| *a | Front view of antenna connector (to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of antenna connector (to Navigation ECU Assembly) |
| *c | Front view of antenna connector (to Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - C-2 (GPS1) | Always | Below 1 Ω |
| B-2a - C-2a | Always | Below 1 Ω |
| B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Procedure1
| *a | Component without harness connected (Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 2 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Replace the antenna divider with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL