This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit |
·
Harness or connector
·
Speaker
·
Radio and display receiver assembly
·
Stereo component equalizer assembly* |
Navigation System | A |
*: w/ Active Noise Control System
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Pre-procedure1
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Active Noise Control System | A |
| w/o Active Noise Control System | B |
A
B
Pre-procedure1
Disconnect the I16 radio and display receiver assembly connector.
Disconnect the S25 stereo component equalizer assembly connector.
Disconnect the O9 and P9 rear speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I16,S25,O9,P9)Location & Routingewd_type=routing;type=c,c,c,c;code=I16,S25,O9,P9 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=8,23,9,24 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| I16-1 (FR+) - S25-8 (FRI+) | Always | Below 1 Ω |
| I16-6 (FR-) - S25-23 (FRI-) | Always | Below 1 Ω |
| I16-2 (FL+) - S25-9 (FLI+) | Always | Below 1 Ω |
| I16-7 (FL-) - S25-24 (FLI-) | Always | Below 1 Ω |
| I16-4 (RR+) - O9-2 (+) | Always | Below 1 Ω |
| I16-9 (RR-) - O9-1 (-) | Always | Below 1 Ω |
| I16-3 (RL+) - P9-2 (+) | Always | Below 1 Ω |
| I16-8 (RL-) - P9-1 (-) | Always | Below 1 Ω |
| I16-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I16-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| I16-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I16-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| I16-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| I16-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| I16-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| I16-8 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Replace the stereo component equalizer assembly.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Pre-procedure1
Disconnect the I16 radio and display receiver assembly connector.
Disconnect the M9 and N7 front No. 1 speaker assembly connectors.
Disconnect the J1 and L3 front No. 3 speaker assembly connectors.
Disconnect the O9 and P9 rear speaker assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I16,J1,L3,M9,N7,O9,P9)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=I16,J1,L3,M9,N7,O9,P9 Click Connector(J1)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J1;pinno=4,2,3,1 Click Connector(L3)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L3;pinno=4,2,3,1 Click Connector(M9)Body>Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=M9;pinno=2,1 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| I16-1 (FR+) - J1-4 (+) | Always | Below 1 Ω |
| I16-6 (FR-) - J1-2 (-) | Always | Below 1 Ω |
| I16-2 (FL+) - L3-4 (+) | Always | Below 1 Ω |
| I16-7 (FL-) - L3-2 (-) | Always | Below 1 Ω |
| J1-3 (TWR+) - M9-2 (+) | Always | Below 1 Ω |
| J1-1 (TWR-) - M9-1 (-) | Always | Below 1 Ω |
| L3-3 (TWL+) - N7-2 (+) | Always | Below 1 Ω |
| L3-1 (TWL-) - N7-1 (-) | Always | Below 1 Ω |
| I16-4 (RR+) - O9-2 (+) | Always | Below 1 Ω |
| I16-9 (RR-) - O9-1 (-) | Always | Below 1 Ω |
| I16-3 (RL+) - P9-2 (+) | Always | Below 1 Ω |
| I16-8 (RL-) - P9-1 (-) | Always | Below 1 Ω |
| I16-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I16-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| I16-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I16-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| J1-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| J1-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L3-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I16-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| I16-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| I16-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| I16-8 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Replace the front No. 3 speaker assembly with a new or known good one.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
No DTCs are output
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL