The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Active Noise Control System | A |
| w/o Active Noise Control System | B |
A
B
Disconnect the I8 and I7 radio receiver assembly connectors.
Disconnect the S25 stereo component equalizer assembly connector.
Disconnect the P9 and/or O9 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I8,S25,I7,P9)Location & Routingewd_type=routing;type=c,c,c,c;code=I8,S25,I7,P9 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=24,9 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| I8-2 (FL+) - S25-24 (FLI-) | Always | Below 1 Ω |
| I8-6 (FL-) - S25-9 (FLI+) | Always | Below 1 Ω |
| I7-2 (RL+) - P9-2 (+) | Always | Below 1 Ω |
| I7-6 (RL-) - P9-1 (-) | Always | Below 1 Ω |
| I8-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I8-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I7-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I7-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I8,S25,I7,O9)Location & Routingewd_type=routing;type=c,c,c,c;code=I8,S25,I7,O9 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=8,23 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 |
||
| I8-1 (FR+) - S25-8 (FRI+) | Always | Below 1 Ω |
| I8-5 (FR-) - S25-23 (FRI-) | Always | Below 1 Ω |
| I7-1 (RR+) - O9-2 (+) | Always | Below 1 Ω |
| I7-3 (RR-) - O9-1 (-) | Always | Below 1 Ω |
| I8-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I8-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I7-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I7-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component equalizer assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL ECU>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I8 and I7 radio receiver assembly connectors.
Disconnect the N7 and/or M9 front No. 1 speaker assembly connector.
Disconnect the L3 and/or J1 front No. 3 speaker assembly connector.
Disconnect the P9 and/or O9 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I8,L3,N7,I7,P9)Location & Routingewd_type=routing;type=c,c,c,c,c;code=I8,L3,N7,I7,P9 Click Connector(L3)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L3;pinno=4,2,3,1 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| I8-2 (FL+) - L3-4 (+) | Always | Below 1 Ω |
| I8-6 (FL-) - L3-2 (-) | Always | Below 1 Ω |
| L3-3 (TWL+) - N7-2 (+) | Always | Below 1 Ω |
| L3-1 (TWL-) - N7-1 (-) | Always | Below 1 Ω |
| I7-2 (RL+) - P9-2 (+) | Always | Below 1 Ω |
| I7-6 (RL-) - P9-1 (-) | Always | Below 1 Ω |
| I8-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I8-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L3-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I7-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I7-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I8,J1,M9,I7,O9)Location & Routingewd_type=routing;type=c,c,c,c,c;code=I8,J1,M9,I7,O9 Click Connector(J1)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J1;pinno=4,2,3,1 Click Connector(M9)Body>Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=M9;pinno=2,1 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 |
||
| I8-1 (FR+) - J1-4 (+) | Always | Below 1 Ω |
| I8-5 (FR-) - J1-2 (-) | Always | Below 1 Ω |
| J1-3 (TWR+) - M9-2 (+) | Always | Below 1 Ω |
| J1-1 (TWR-) - M9-1 (-) | Always | Below 1 Ω |
| I7-1 (RR+) - O9-2 (+) | Always | Below 1 Ω |
| I7-3 (RR-) - O9-1 (-) | Always | Below 1 Ω |
| I8-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I8-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| J1-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| J1-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I7-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I7-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG