Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467509 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15CB11 Telephone Main Antenna Circuit Short to Ground Telephone antenna (main) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Roof antenna assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Telephone transceiver assembly


Telematics A
B15CB13 Telephone Main Antenna Circuit Open Telephone antenna (Main) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Roof antenna assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Telephone transceiver assembly


Telematics A

WIRING DIAGRAM

E464138E08
2.313,0.385 2.469,0.583 0.156,0.198 10 false A 2.313,0.969 2.469,1.167 0.156,0.198 10 false A 3.885,0.385 4.042,0.583 0.156,0.198 10 false B 3.885,0.969 4.042,1.167 0.156,0.198 10 false B 5.458,0.979 5.615,1.177 0.156,0.198 10 false C 5.458,0.385 5.615,0.583 0.156,0.198 10 false C 2.323,0.167 2.479,0.365 0.156,0.198 10 false 4 3.896,0.156 4.052,0.354 0.156,0.198 10 false 3 5.458,0.167 5.615,0.365 0.156,0.198 10 false 1 5.427,0.76 5.656,0.99 0.229,0.229 10 false 1a 3.854,0.75 4.083,0.979 0.229,0.229 10 false 3a 2.281,0.75 2.51,0.979 0.229,0.229 10 false 4a 5.76,0.375 6.354,0.573 0.594,0.198 10 false ANT1 5.625,1.979 7,2.469 1.375,0.49 10 false Telephone Transceiver Assembly 4.156,2.042 5.396,2.49 1.24,0.448 10 false Antenna Cord Sub-assembly 2.563,2 3.792,2.448 1.229,0.448 10 false No. 3 Antenna Cord Sub-assembly 0.865,2.01 2.469,2.281 1.604,0.271 10 false Roof Antenna Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



HINT:

Refer to "PARTS LOCATION" for the installation location of telephone and GPS antenna cord.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PARTS LOCATION


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTC are not output. A
DTCs are output. B



Post-procedure1

d.

None



A

B

2.INSPECT ROOF ANTENNA ASSEMBLY
2.INSPECT ROOF ANTENNA ASSEMBLY
a.
E271865C57
1.969,1.479 2.24,1.594 false 2.292,1.531 2.604,1.729 0.313,0.198 10 false 4a 0.865,0.208 1.177,0.406 0.313,0.198 10 false *a
*a Component without harness connected
(Roof Antenna Assembly)


Remove the roof antenna assembly.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 9 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.
E462683C02
0.271,1.031 0.583,1.344 0.313,0.313 0.521,3.542 0.823,3.813 0.302,0.271 2,3.875 2.354,4.313 2.354,4.313 2.51,4.313 true 1.573,1.198 1.229,1.448 1.229,1.448 1.063,1.448 true 0.26,0.219 0.573,0.417 0.313,0.198 10 false *a 0.292,1.969 0.604,2.167 0.313,0.198 10 false *b 0.354,1.104 0.667,1.302 0.313,0.198 10 false A 0.625,3.615 0.938,3.813 0.313,0.198 10 false B 0.854,1.344 1.167,1.542 0.313,0.198 10 false 4a 2.563,4.229 2.875,4.427 0.313,0.198 10 false 3a
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the roof antenna assembly connector.


b.

Disconnect the antenna connector from the antenna cord sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Always Below 1 Ω
A-4a - B-3a Always Below 1 Ω
A-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.
E464139C05
1.542,0.156 1.854,0.469 0.313,0.313 0.906,2.219 1.208,2.49 0.302,0.271 1.479,1.271 1.906,1.552 1.906,1.552 2.063,1.552 true 1.75,2.438 2.198,2.146 2.198,2.146 2.354,2.146 true 1.781,2.656 2.177,2.885 2.177,2.885 2.333,2.885 true 0.26,0.219 0.573,0.417 0.313,0.198 10 false *a 0.292,1.969 0.604,2.167 0.313,0.198 10 false *b 1.656,0.229 1.969,0.427 0.313,0.198 10 false B 1.01,2.292 1.323,2.49 0.313,0.198 10 false C 2.135,1.479 2.448,1.677 0.313,0.198 10 false 3a 2.396,2.802 2.708,3 0.313,0.198 10 false 1a 2.458,2.063 2.896,2.292 0.438,0.229 10 false ANT1
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna connector from the telephone transceiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-3 - C-1 (ANT1) Always Below 1 Ω
B-3a - C-1a Always Below 1 Ω
B-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT