Home › General › MAINTENANCE › FRONT DISC BRAKE PAD
RM38G0E _V1 General _100461 MAINTENANCE _0468807 FRONT DISC BRAKE PAD A

MAINTENANCE  FRONT DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455948N01
1.667,2.667 2.833,3.833 1.167,1.167 1.667,4.333 2.917,5.333 1.25,1 0.25,4 1.583,5 1.333,1 3,4.583 4.333,5.583 1.333,1 6.448,0.167 6.865,0.167 false 6.458,0.583 6.792,0.583 false 5.417,2.083 5.417,1.583 5.417,1.583 5.667,1.583 false 2.219,4.333 2.219,4.031 2.219,4.031 2.469,4.031 false 4.333,5.083 4.667,5.083 false 0.917,4 0.917,3.667 0.917,3.667 1.167,3.667 false 2.333,2.896 2.5,2.896 2.5,2.896 2.5,3.229 false 3.417,5.188 3.417,5.354 3.417,5.354 3.583,5.354 false 1.167,4.375 1.167,4.208 1.167,4.208 1.333,4.208 false 3.917,4.969 3.917,4.719 3.917,4.719 4.083,4.719 false 0.698,4.594 0.698,4.844 0.698,4.844 0.865,4.844 false 1.938,3.25 2.104,3.25 false 3.063,3.833 3.229,3.833 3.229,3.833 3.229,3.5 false 2,4.896 2,5.167 2,5.167 2.667,5.167 false 2.5,5 2.5,5.167 false 2.25,2.667 2.25,2.333 2.25,2.333 2.5,2.333 false 2.979,3.5 3.396,3.5 false 6.271,0.042 6.521,0.375 0.25,0.333 18 false 1 6.281,0.458 6.531,0.792 0.25,0.333 18 false 2 5.719,1.458 5.969,1.792 0.25,0.333 18 false 3 2.854,2.188 3.188,2.604 0.333,0.417 18 false 4 2.802,3.927 3.052,4.26 0.25,0.333 18 false 5 4.719,4.948 4.969,5.281 0.25,0.333 18 false 6 1.219,3.542 1.469,3.875 0.25,0.333 18 false 6 2.167,2.833 2.583,3.083 0.417,0.25 10 false *1 3.635,5.292 3.885,5.542 0.25,0.25 10 false *2 1.385,4.146 1.635,4.396 0.25,0.25 10 false *2 4.135,4.667 4.385,4.917 0.25,0.25 10 false *3 0.917,4.781 1.167,5.031 0.25,0.25 10 false *3 1.771,3.177 2.188,3.427 0.417,0.25 10 false *4 3.448,3.438 3.865,3.688 0.417,0.25 10 false *5 2.719,5.104 2.969,5.354 0.25,0.25 10 false *6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 FRONT WHEEL - - - -
4 FRONT DISC BRAKE FITTING KIT 04947 (Click here) - -
5 FRONT DISC BRAKE PAD KIT 04465 (Click here) - -
6 FRONT ANTI SQUEAL SHIM KIT 04945 - - -

*1 FRONT DISC BRAKE ANTI-RATTLE SPRING *2 FRONT NO. 1 DISC BRAKE ANTI-SQUEAL SHIM
*3 FRONT NO. 2 DISC BRAKE ANTI-SQUEAL SHIM *4 PIN HOLD CLIP
*5 FRONT DISC BRAKE ANTI-RATTLE PIN WITH HOLE *6 FRONT DISC BRAKE PAD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front disc brake pad removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 04947 4.REMOVE FRONT DISC BRAKE FITTING KIT

a.
C456318N01
0.167,0.083 0.5,0.417 0.333,0.333 18 false i

i.

Disengage the hook from the disc brake cylinder assembly and remove the pin hold clip from the front disc brake anti-rattle pin with hole.



b.
C456319N01
0.417,0.052 0.667,0.385 0.25,0.333 18 false i 4.135,0.052 4.385,0.385 0.25,0.333 18 false ii

i.

While pressing the front disc brake anti-rattle spring, remove the front disc brake anti-rattle pin with hole (upper side).


ii.

Disengage the front disc brake anti-rattle spring from the front disc brake pads and remove the front disc brake anti-rattle pin with hole (lower side).



c.
C456321N01
0.167,0.083 0.583,0.417 0.417,0.333 18 false i

i.

Remove the front disc brake anti-rattle spring.



Hide 04465 5.REMOVE FRONT DISC BRAKE PAD KIT

Z101186

NOTICE:

Be sure to inspect the front disc when replacing the front disc brake pads with new ones.

Click here(Click here)



a.
C456322


Hide 04945 6.REMOVE FRONT ANTI SQUEAL SHIM KIT

a.
C456323C01
3,0.583 3,0.333 3,0.333 3.917,0.333 false 3.667,0.75 3.667,0.333 false 4.5,0.885 4.5,0.552 4.5,0.552 4.75,0.552 false 5.167,1.052 5.167,0.719 5.167,0.719 5.417,0.719 false 2.333,0.448 2.333,0.198 2.333,0.198 2.583,0.198 false 1.75,0.333 1.75,0.083 1.75,0.083 2,0.083 false 3.969,0.271 4.302,0.521 0.333,0.25 10 false *1 2.635,0.135 2.969,0.385 0.333,0.25 10 false *2 5.469,0.656 5.802,0.906 0.333,0.25 10 false *3 2.052,0.021 2.385,0.271 0.333,0.25 10 false *3 4.802,0.49 5.052,0.74 0.25,0.25 10 false *2
*1 Front Disc Brake Pad *2 Front No. 1 Disc Brake Anti-Squeal Shim
*3 Front No. 2 Disc Brake Anti-Squeal Shim - -