| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FRONT FLEXIBLE HOSE | 47313J | ( ) |
- | - |
| *A | for LH Side | - | - |
| *1 | BRAKE TUBE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part | - | - |
| *A | for RH Side | *B | w/ Electronic-Kinetic Dynamic Suspension System |
| *1 | BRAKE TUBE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part | - | - |
| *A | for LH Side | *B | for RH Side |
Because the left and right front flexible hoses are not interchangeable, verify the part number when installing the front flexible hoses.
When reusing the front flexible hoses, use the identification marks created during removal to install each front flexible hose to its original position.
47313J 1.INSTALL FRONT FLEXIBLE HOSE (for LH Side)
|
|
| *a | Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Install the front flexible hose with a new clip.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the front flexible hose while holding the front flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
Install the front flexible hose with the 2 bolts.
Do not twist the front flexible hose when installing it.
Connect the front flexible hose to the disc brake cylinder assembly with a new union bolt and a new gasket.
Install the front flexible hose lock securely into the lock hole in the disc brake cylinder assembly.
Do not twist the front flexible hose when installing it.
47315B 2.INSTALL BRAKE TUBE FLEXIBLE HOSE (for RH Side)
|
|
| *a | Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Install the front front brake tube flexible hose with 2 new clips.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the front brake tube flexible hose while holding the front brake tube flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)):
14.2 N*m (145 kgf*cm, 10 ft.*lbf)
47311G 3.INSTALL BRAKE TUBE FLEXIBLE HOSE (for RH Side)
|
|
| *a | Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Install the front front brake tube flexible hose with 2 new clips.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the front brake tube flexible hose while holding the front brake tube flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)):
14.2 N*m (145 kgf*cm, 10 ft.*lbf)
4.CONNECT FRONT STABILIZER CONTROL TUBE ASSEMBLY (for RH Side, w/ Electronic-Kinetic Dynamic Suspension System)
47393 5.INSTALL BRAKE TUBE HEAT INSULATOR (for RH Side)
47394 6.INSTALL NO. 2 BRAKE TUBE HEAT INSULATOR (for RH Side)
47313A 7.INSTALL FRONT FLEXIBLE HOSE (for RH Side)
|
|
Use the same procedure as for the LH side.
53785B 8.INSTALL FRONT FENDER APRON TRIM PACKING D (for LH Side)
53784 9.INSTALL FRONT FENDER APRON TRIM PACKING C (for RH Side)
11.BLEED BRAKE LINE
12.INSTALL FRONT WHEEL
13. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART