| *1 | REAR NO. 1 DISC BRAKE CYLINDER SLIDE PIN | *2 | REAR NO. 2 DISC BRAKE CYLINDER SLIDE PIN |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
Lithium Soap Base Glycol Grease | - | - |
| *A | w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY | - | - |
| *1 | REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM | *2 | REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM |
| *3 | REAR DISC BRAKE PAD WEAR INDICATOR PLATE | *4 | REAR DISC BRAKE PAD |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
Lithium soap base glycol grease |
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
42431 1.INSTALL REAR DISC
| *a | Matchmark | - | - |
Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.
When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.
47822 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING
3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT
|
Lithium Soap Base Glycol Grease | - | - |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.
Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each rear disc brake bushing dust boot.
Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.
4.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING
|
Lithium Soap Base Glycol Grease | - | - |
Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.
Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.
5.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
| *1 | Rear No. 1 Disc Brake Cylinder Slide Pin | *2 | Rear No. 2 Disc Brake Cylinder Slide Pin |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.
Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.
Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.
6.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE
|
|
04466 8.INSTALL REAR DISC BRAKE PAD KIT
|
|
47850 9.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 bolts.
If bleeding of air from the rear brake cylinder assembly will be performed, reuse the bolts. If bleeding of air from the rear brake cylinder assembly will not be performed, install new bolts.
46310C 11.INSTALL PARKING BRAKE ACTUATOR SEAL
|
|
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
47319F 14.CONNECT REAR FLEXIBLE HOSE
Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.
46170 15.INSTALL PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Perform the following procedure:
1. Connect the reservoir level switch connector.
2. Connect the cable to the negative (-) battery terminal.
for 1GR-FE:
Click hereGeneral>MAINTENANCE>1GR-FE BATTERY>INSTALLATION
for V35A-FTS:
Perform the following procedure if air bleeding is not necessary:
1. Turn the ignition switch to ON.
2. Depress the brake pedal and release it.
3. Clear the DTCs.
17. BLEED BRAKE LINE
47850 18.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY
|
|
| *a | Brake Warning Light (Yellow) | - | - |
Perform the following procedure:
w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY:
Remove the parking brake actuator protector assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Disconnect the No. 2 parking brake wire assembly connector.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Remove the parking brake actuator assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Turn the T50 "TORX" socket wrench clockwise until it stops. *1
Turn the T50 "TORX" socket wrench counterclockwise until it stops. *2
Repeat steps (*1) through (*2) 5 times.
Turn the T50 "TORX" socket wrench clockwise until it stops.
Remove the parking brake actuator seal.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Install a new parking brake actuator seal.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
Install the parking brake actuator assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
Connect the No. 2 parking brake wire assembly connector.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
except 1GR-FE:
for LHD:
Remove the engine side cover LH.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL
for RHD:
Remove the engine side cover RH.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL
Remove the brake master cylinder reservoir filler cap assembly.
Force air within the rear disc brake cylinder assembly to accumulate at the rear disc brake bleeder plug.(*1)
Disable brake control.
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
Disconnect the No. 2 parking brake wire assembly connector.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting.
Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.
Temporarily install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
Connect the No. 2 parking brake wire assembly connector.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
Connect the reservoir level switch connector.
Connect the cable to the negative (-) battery terminal.
for 1GR-FE:
Click hereGeneral>MAINTENANCE>1GR-FE BATTERY>INSTALLATION
for V35A-FTS:
Turn the ignition switch to ON.
Depress the brake pedal and release it.
Apply the parking brake.
Enter ECB (Electronically Controlled Brake system) Deactivate Mode.(*2)
Performing the following procedure enters ECB (Electronically Controlled Brake system) Deactivate Mode without using the GTS.
ECB (Electronically Controlled Brake system) Deactivate Mode allows the brake lines to be bled without using the GTS.
The brake warning light blinks (yellow) to indicate that ECB (Electronically Controlled Brake system) Deactivate Mode is selected.
Be sure to confirm that the brake warning light is blinking (yellow) throughout the brake line bleeding procedure.
If any of the following conditions are met, ECB (Electronically Controlled Brake system) Deactivate Mode is canceled and the brake warning light (yellow) turns off. Do not allow ECB (Electronically Controlled Brake system) Deactivate Mode to be canceled while bleeding the brake lines or DTCs may be stored.
| The shift lever is moved from P to any other position. |
| The ignition switch is turned to ON (Engine start). |
| The ignition switch is turned off. |
| The parking brake is released. |
| The vehicle speed is more than 0 km/h (0 mph). |
Do not rotate any brake disc while ECB (Electronically Controlled Brake system) Deactivate Mode is selected.
Although the brake warning light (yellow) will blink and a buzzer will sound while performing brake line bleeding, this is not a malfunction.
Perform the procedure listed below within 1 minute.
Turn the ignition switch to ON with the shift lever in P and parking brake applied.
Move the shift lever to N and then depress the brake pedal more than 8 times within 5 seconds.
Move the shift lever to P and then depress the brake pedal more than 8 times within 5 seconds.
Move the shift lever to N and then depress the brake pedal more than 8 times within 5 seconds.
Move the shift lever to P.
Check that the brake warning light is blinking (yellow).
Bleed the brake line.(*3)
Remove the rear disc brake bleeder plug cap.
Connect a vinyl tube to the rear disc brake bleeder plug.
Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.(*a)
Depress the brake pedal several times with approximately 1 second between each depression, and then loosen the bleeder plug with the pedal depressed.(*b)
When brake fluid stops coming out, tighten the bleeder plug and then release the brake pedal for 1 second or more.(*c)
When the brake pedal is released, the piston inside the master cylinder may take longer than the brake pedal to return to its original position. Therefore, make sure to wait for 1 second or more between each depression of the brake pedal.
Repeat steps (*a) through (*c) until there are no signs of air in the brake fluid.
Release the parking brake.
Repeat steps (*1) through (*3) 3 times.
If there is still air in the system after performing steps (*1) through (*3) 3 times, repeat the steps (*1) through (*3) until the air has been bled.
Tighten the rear disc brake bleeder plug completely.
10.8 N*m (110 kgf*cm, 8 ft.*lbf)
Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.
Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY:
Install the parking brake actuator protector assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSTALLATION
Inspect for brake fluid leaks.
Adjust the brake fluid level in the reservoir.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION
Install the brake master cylinder reservoir filler cap assembly.
except 1GR-FE:
for LHD:
Install the engine side cover LH.
for RHD:
Install the engine side cover RH.
Turn the ignition switch off.
Clear the DTCs.
19.INSTALL REAR WHEEL
20. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART