| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | REAR BRAKE TUBE FLEXIBLE HOSE | 47321B | ( ) |
- | - |
| 2 | REAR NO. 2 BRAKE TUBE FLEXIBLE HOSE | 47324B | ( ) |
- | - |
| *1 | BRAKE TUBE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | REAR FLEXIBLE HOSE | 47319F | ( ) |
- | - |
| *1 | BRAKE TUBE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | CONNECT CABLE TO NEGATIVE BATTERY TERMINAL | - | ( ) |
- | - |
| 5 | BLEED BRAKE LINE | - | - | ( ) |
- |
| 6 | REAR WHEEL | - | - | - | - |
| 7 | INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL | - | - | - | ( ) |
Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the rear flexible hoses.
When reusing the rear flexible hoses, use the identification marks created during removal to install each rear flexible hose to its original position.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
47321B 1.INSTALL REAR BRAKE TUBE FLEXIBLE HOSE
|
|
| *a | Torque Wrench Fulcrum Length | *b | Union Nut Wrench |
Install the rear brake tube flexible hose with 2 new clips.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the rear brake tube flexible hose while holding the rear brake tube flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
47324B 2.INSTALL REAR NO. 2 BRAKE TUBE FLEXIBLE HOSE
|
|
| *a | Torque Wrench Fulcrum Length | *b | Union Nut Wrench |
Install the rear No. 2 brake tube flexible hose with 2 new clips.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the rear No. 2 brake tube flexible hose while holding the rear No. 2 brake tube flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
47319F 3.INSTALL REAR FLEXIBLE HOSE
|
|
| *a | Torque Wrench Fulcrum Length | *b | Union Nut Wrench |
Install the rear flexible hose with a new clip.
Install the clip as far as it will go.
Using a union nut wrench, connect the brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.
Do not kink or damage the brake tube.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
Install the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.
5.BLEED BRAKE LINE
6.INSTALL REAR WHEEL
7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART