The ECM detects the signal from the transfer L4 position switch.
This DTC indicates that the transfer L4 position switch remains off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P277115 | Four Wheel Drive (4WD) Low Switch Circuit Short to Battery or Open | Transfer L4 position switch remains off while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
·
Output shaft speed is between 1000 and 3000 rpm.
·
Transfer position switch is in L4. |
·
Open in transfer L4 position switch circuit
·
Transfer system
·
ECM |
Comes on | DTC stored | SAE Code: P2774 |
The ECM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case H4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:
The L4 switch indicates that the H4 transfer case gears are engaged.
The transfer position switch is in L4.
The transfer case output shaft speed is between 1000 and 3000 rpm.
The specified time period has elapsed.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the transfer position switch to L4.
Drive the vehicle at 15 to 20 km/h (9 to 12 mph) for 1.8 seconds or more.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P277115.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P277111.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>P277111
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PRECAUTION
Disconnect the 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B8)Location & Routingewd_type=routing;type=c;code=B8 Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECUewd_type=component;type=c;code=B8;pinno=3 |
||
| B8-3 (L4) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>JF2BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the 4 wheel drive control ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B8,B2)Location & Routingewd_type=routing;type=c,c;code=B8,B2 Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECUewd_type=component;type=c;code=B8;pinno=3 |
||
| B8-3 (L4) - B2-35 (L4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG