Home › Suspension › SUSPENSION CONTROL › ADAPTIVE VARIABLE SUSPENSION SYSTEM
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0469072 ADAPTIVE VARIABLE SUSPENSION SYSTEM C

SUSPENSION CONTROL  ADAPTIVE VARIABLE SUSPENSION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0101  Lost Communication with TCM  U0122  Lost Communication With Vehicle Dynamics Control Module  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U1103  Lost Communication with Stop and Start Control Module  


DESCRIPTION

The absorber control ECU receives signals from the ECM, transmission control ECU assembly, No. 2 skid control ECU (brake actuator assembly), steering sensor, yaw rate and acceleration sensor (airbag sensor with ECU assembly) via CAN communication.

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system first.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
U0100 Lost Communication with ECM / PCM "A" While driving at 30 km/h (19 mph) or more, data is not received via CAN communication for 3 seconds or more.
·

ECM

·

CAN communication system

·

Absorber control ECU


Does not come on Yes
U0101 Lost Communication with TCM While driving at 30 km/h (19 mph) or more, data is not received via CAN communication for 6 seconds or more.
·

TCM

·

CAN communication system

·

Absorber control ECU


Does not come on Yes
U0122 Lost Communication With Vehicle Dynamics Control Module Data is not received from the No. 2 skid control ECU (brake actuator assembly) via CAN communication for 3 seconds or more.
·

No. 2 skid control ECU (brake actuator assembly)

·

CAN communication system

·

Absorber control ECU


Does not come on Yes
U0124 Lost Communication with Lateral Acceleration Sensor Module Data is not received from the yaw rate and acceleration sensor (airbag sensor with ECU assembly) via CAN communication for 3 seconds or more.
·

Yaw rate and acceleration sensor (airbag sensor with ECU assembly)

·

CAN communication system

·

Absorber control ECU


Does not come on Yes
U0126 Lost Communication with Steering Angle Sensor Module Data is not received from the steering sensor via CAN communication for 3 seconds or more.
·

Steering sensor

·

CAN communication system

·

Absorber control ECU


Does not come on Yes
U1103 Lost Communication with Stop and Start Control Module While driving at 30 km/h (19 mph) or more, data is not received via CAN communication for 3 seconds or more.
·

Engine stop and start ECU

·

CAN communication system

·

Absorber control ECU


Does not come on Yes

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If DTC C1782 (Power Source Voltage Malfunction) is output at the same time, perform troubleshooting for C1782 first.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>C1782

·

Before replacing the absorber control ECU, perform all of the following:

-

DTC inspection.

*

If no malfunctions are found in other areas, replace the absorber control ECU.



·

After replacing the absorber control ECU with a new one, perform registration of vehicle identification information.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK FOR DTCS
a.

Clear the DTCs.

Chassis > Adaptive Variable Suspension System > Clear DTCs
50002 171

b.

Drive the vehicle at a speed of 30 km/h (19 mph) or more for 10 seconds or more.


c.

Check for DTCs.

Chassis > Adaptive Variable Suspension System > Trouble Codes
50001 171
Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



HINT:

If a CAN communication malfunction DTC and a related sensor malfunction DTC are output at the same time, the CAN communication malfunction must be repaired before troubleshooting the sensor.



A

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)