The forward recognition camera receives vehicle information from the ECM via the CAN communication line.
When the forward recognition camera is unable to determine the vehicle information from the vehicle information sent from the ECM, the forward recognition camera outputs U030051.
When the vehicle information sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U030051 | Internal Control Module Software Incompatibility Not Programmed | The forward recognition camera cannot confirm the vehicle information from the ECM. |
·
Forward recognition camera
·
SFI system
·
ECM |
Front Recognition Camera | B |
| U030057 | Internal Control Module Software Incompatibility Invalid/Incompatible Software Component | The vehicle information from the ECM and that stored in the forward recognition camera do not match. |
·
Forward recognition camera
·
SFI system
·
ECM |
Front Recognition Camera | B |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
When replacing the ECM, refer to Service Bulletin.
Check for DTCs.
| Result | Proceed to |
|---|---|
| SFI system DTC is not output | A |
| SFI system DTC is output | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, perform a health check.
ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| HV/EV Equipped Information | Vehicle information (engine) stored by forward recognition camera | Non-HV/EV or HV/EV | Non-HV/EV: Gasoline Model HV/EV: HV Model |
- |
| Tester Display |
|---|
| HV/EV Equipped Information |
When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.
When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.
| Result | Proceed to |
|---|---|
| Specification stored by the forward recognition camera and vehicle specification do not match | A |
| Specification stored by the forward recognition camera and vehicle specification match | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL