Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › 2021.04–2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468040 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E465320N02
4.344,1.063 6.833,2.615 2.49,1.552 4.385,2.927 6.875,4.479 2.49,1.552 4.885,1.896 5.219,1.896 false 5.583,1.875 6.031,1.875 false 4.375,0.771 4.729,0.771 false 1.708,3.5 1.708,3.969 false 4.906,3.771 5.198,3.771 false 1.625,4.01 1.906,4.365 0.281,0.354 18 false 1 4.719,1.76 5,2.115 0.281,0.354 18 false 3 5.094,0.583 5.375,0.938 0.281,0.354 18 false 2 6.448,1.115 6.906,1.313 0.458,0.198 10 false x 3 6.448,3.073 6.906,3.271 0.458,0.198 10 false x 3 4.719,3.615 5,3.969 0.281,0.354 18 false 3 4.427,1.115 4.802,1.354 0.375,0.24 12 false *A 4.469,2.99 4.844,3.229 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT BUMPER ASSEMBLY - - - -
2 FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH 53808D (Click here) - -
3 HEADLIGHT ASSEMBLY LH - (Click here) - -

*A w/ Headlight ECU *B w/o Headlight ECU

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during headlight assembly LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Front bumper assembly (Including removal and installation)
w/ Parking Support Brake System:
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Front television camera assembly, front bumper assembly or radiator grille
·

Television camera view adjustment

HINT:

Replacement or removal and installation of 2 or more parts


·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Headlight ECU sub-assembly LH
w/ Adaptive Variable Suspension System:

Synchronize the vehicle information


Automatic headlight beam level control system (Click here)
w/o Adaptive Variable Suspension System:
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 53808D 2.REMOVE FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH

a.
E468464C01
0.458,0.125 0.74,0.479 0.281,0.354 18 true i 3.875,0.135 4.156,0.49 0.281,0.354 18 true ii 0.49,1.99 0.771,2.344 0.281,0.354 18 true iii 3.844,1.99 4.125,2.344 0.281,0.354 18 true iv
V113147

Push in this Direction
V113148

Remove in this Direction (1)
V113149

Remove in this Direction (2)
V100135

Clip


i.

Using a clip remover, detach the clip.


ii.

Push in the illustration and detach the claw in the direction (1) as shown in the illustration.


iii.

Push in the illustration and detach the claw in the direction (1) as shown in the illustration.


iv.

Using a moulding remover, detach the 3 clips and remove the front fender reinforcement sub-assembly top LH in the direction (2) as shown in the illustration.



Hide 3.REMOVE HEADLIGHT ASSEMBLY LH

a.
E469503C01
3.479,0.094 6.656,1.813 3.177,1.719 0.313,1.969 3.271,3.625 2.958,1.656 0.646,0.313 0.927,0.667 0.281,0.354 18 true i 3.813,0.167 4.094,0.521 0.281,0.354 18 true ii 0.635,2.021 0.917,2.375 0.281,0.354 18 true iii 3.573,2 3.854,2.354 0.281,0.354 18 false iv 3.563,0.188 3.938,0.427 0.375,0.24 12 false *A 0.375,2.063 0.75,2.302 0.375,0.24 12 false *B
*A w/ Headlight ECU *B w/o Headlight ECU
V113147

Remove in this Direction
V100135

Connector
V100136

Bolt
V100137

Screw


i.

Apply protective tape around the headlight assembly LH.


ii.

w/ Headlight ECU:

Release the connector lock lever and disconnect the connector as shown in the illustration.


iii.

w/o Headlight ECU:

Disconnect the connector.


iv.

Remove the bolt and 3 screws.



b.
E465324C02
0.458,0.052 0.833,0.417 0.375,0.365 18 true i,ii 3.917,0.063 4.229,0.396 0.313,0.333 18 true iii
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Place your hands at the positions shown in the illustration and remove the bracket from the guide.

NOTICE:

Do not break the bracket.



ii.

Slide the headlight assembly LH in the removal direction (1) and detach the guide.


iii.

Remove the headlight assembly LH in the removal direction (2) as shown in the illustration.