The forward recognition camera receives vehicle information (Conv/HV/EV) from the ECM via the CAN communication line.
When the forward recognition camera is unable to determine the vehicle information (Conv/HV/EV) from the vehicle information (Conv/HV/EV) sent from the ECM, the forward recognition camera outputs U030051.
When the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U030051 | Internal Control Module Software Incompatibility Not Programmed | Once 3 seconds elapse after turning the ignition switch to ON, the system is unable to determine the vehicle information (Conv/HV/EV) sent from the ECM and vehicle information (Conv/HV/EV) sent from the forward recognition camera for approximately 3 seconds or more. |
·
SFI system
·
Forward recognition camera |
Pre-Collision System | B |
| U030057 | Internal Control Module Software Incompatibility Invalid / Incompatible Software Component | Once 3 seconds elapse after turning the ignition switch to ON, the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera for approximately 1 second or more. |
·
SFI system
·
Forward recognition camera |
Pre-Collision System | B |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
Before replacing the ECM, refer to Service Bulletin.
Check for DTCs.
If the pre-collision system outputs U030051 or U030057, SFI system DTCs may also have been output. Check the SFI system first.
| Result | Proceed to |
|---|---|
| SFI system DTC are not output | A |
| SFI system DTC are output | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, perform the Health Check.
Check for DTCs.
ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Information (Conv/HV/EV) | Vehicle information (Conv/HV/EV) | Unknown, Conv or HV/EV | Unknown: Vehicle information not confirmed Conv: Conventional HV/EV: HV |
- |
| Tester Display |
|---|
| Vehicle Information (Conv/HV/EV) |
When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.
When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.
| Result | Proceed to |
|---|---|
| Specification stored by the forward recognition camera and vehicle specification do not match | A |
| "Unknown" is displayed | |
| Specification stored by the forward recognition camera and vehicle specification match | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL