Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU)
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  High Beam Headlight Circuit  


DESCRIPTION

The headlight ECU sub-assembly controls the high beam headlights.

WIRING DIAGRAM

w/ Adaptive High Beam System
E444734E05
5.146,3.24 7.156,3.521 2.01,0.281 10 false B 5.771,1.302 6.521,1.542 0.75,0.24 10 false PSWL1+ 5.771,1.667 6.396,1.917 0.625,0.25 10 false PSWL1- 2.198,3 4.354,3.24 2.156,0.24 10 false Headlight Unit Assembly 1.021,2.292 2.833,2.615 1.813,0.323 10 false H 0.844,1.583 2.49,1.885 1.646,0.302 10 false Lo/Hi Beam Shade 5.427,1.25 5.698,1.51 0.271,0.26 10 false 13 5.51,1.563 5.781,1.823 0.271,0.26 10 false 3 3.323,1.26 3.594,1.521 0.271,0.26 10 false 6 3.313,1.573 3.583,1.833 0.271,0.26 10 false 4 5.156,3.396 7.104,3.677 1.948,0.281 10 false Headlight ECU Sub-assembly 1.031,2.469 2.844,2.792 1.813,0.323 10 false Headlight Unit

w/o Adaptive High Beam System
E471203E01
1.021,3.052 2.552,3.25 1.531,0.198 10 false Headlight Unit 3.792,1.917 4.76,2.771 0.969,0.854 10 false Electronic Light Source Control Gear 0.594,1.281 2.125,1.479 1.531,0.198 10 false Lo/Hi Beam Shade 0.979,2.344 2.51,2.542 1.531,0.198 10 false Hi Beam 2.167,3.615 3.948,3.979 1.781,0.365 10 false Headlight Unit Assembly 5.813,4.031 7.063,4.698 1.25,0.667 10 false Headlight ECU Sub-assembly LH 5.771,3.844 7.156,4.448 1.385,0.604 10 false B 2.823,1.042 4.354,1.24 1.531,0.198 10 false H 2.813,1.448 4.344,1.646 1.531,0.198 10 false H 2.833,2.156 4.365,2.354 1.531,0.198 10 false J 2.813,2.594 4.344,2.792 1.531,0.198 10 false J 3.542,2.583 5.073,2.781 1.531,0.198 10 false I 3.542,2.167 5.073,2.365 1.531,0.198 10 false I 4.99,2.167 6.521,2.365 1.531,0.198 10 false I 4.99,2.594 6.521,2.792 1.531,0.198 10 false I 5.948,1.052 6.802,1.719 0.854,0.667 10 false PSWL1+ 5.927,1.469 6.781,2.135 0.854,0.667 10 false PSWL1- 5.625,0.948 6.479,1.615 0.854,0.667 10 false 13 5.625,1.365 6.479,2.031 0.854,0.667 10 false 3 2.833,0.854 3.688,1.521 0.854,0.667 10 false 6 2.823,1.271 3.677,1.938 0.854,0.667 10 false 4 2.833,1.979 3.688,2.646 0.854,0.667 10 false 2 2.802,2.406 3.656,3.073 0.854,0.667 10 false 1 3.542,1.979 4.396,2.646 0.854,0.667 10 false 2 4.958,2.396 5.813,3.063 0.854,0.667 10 false 1 4.99,1.979 5.844,2.646 0.854,0.667 10 false 5 3.521,2.396 4.375,3.063 0.854,0.667 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Type Diagnostic Note
High Beam Headlight High beam headlights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
High Beam Headlight
50004 449 52
OK:

High beam headlights turn on.



Result:
Result Proceed to
OK A
NG (LH side high beam light does not illuminate) B
NG (RH side high beam light does not illuminate) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HEADLIGHT UNIT ASSEMBLY LH

C

8.CHECK HEADLIGHT UNIT ASSEMBLY RH
2.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

3.CHECK OPERATION (HIGH BEAM HEADLIGHT)
3.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Result Proceed to
OK A
NG (w/ Adaptive High Beam System) B
NG (w/o Adaptive High Beam System) C



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

4.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

5.INSPECT HEADLIGHT UNIT ASSEMBLY LH
4.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E471200C01
2.042,0.448 2.406,0.75 0.365,0.302 5.219,0.802 5.583,1.104 0.365,0.302 1.521,2.115 1.802,1.667 true 1.792,1.406 1.573,0.927 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 2.177,0.521 2.49,0.719 0.313,0.198 10 false B 5.365,0.906 5.677,1.104 0.313,0.198 10 false H 1.271,0.75 1.948,0.969 0.677,0.219 10 false PSWL1- 1.229,2.156 1.906,2.375 0.677,0.219 10 false PSWL1+
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)


a.

Remove the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-13 (PSWL1+) - H-6 Always Below 1 Ω
B-3 (PSWL1-) - H-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

5.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E471204C01
1.875,0.479 2.271,0.719 0.396,0.24 4.979,0.615 5.375,0.854 0.396,0.24 5.052,2.281 5.448,2.521 0.396,0.24 1.823,2.219 2.219,2.458 0.396,0.24 1.938,1.854 1.656,1.521 true 1.615,1.271 1.396,0.792 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 1.135,2.125 1.448,2.323 0.313,0.198 10 false *c 2.031,0.542 2.344,0.74 0.313,0.198 10 false B 5.156,0.677 5.469,0.875 0.313,0.198 10 false H 1.104,0.625 1.781,0.844 0.677,0.219 10 false PSWL1- 2.021,1.813 2.698,2.031 0.677,0.219 10 false PSWL1+ 4.427,0.406 4.74,0.604 0.313,0.198 10 false *b 2.01,2.281 2.323,2.479 0.313,0.198 10 false I 5.219,2.344 5.531,2.542 0.313,0.198 10 false J 4.479,2.094 4.792,2.292 0.313,0.198 10 false *b
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)
*c Component without harness connected
(to Headlight Unit Assembly LH)
- -


a.

Remove the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-13 (PSWL1+) - H-6 Always Below 1 Ω
B-3 (PSWL1-) - H-4 Always Below 1 Ω
B-13 (PSWL1+) - I-5 Always Below 1 Ω
B-3 (PSWL1-) - I-1 Always Below 1 Ω
J-2 - I-2 Always Below 1 Ω
J-1 - I-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HEADLIGHT UNIT LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

6.CHECK HEADLIGHT UNIT LH
a.

Replace the headlight unit LH with a know good one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

7.CHECK OPERATION (HIGH BEAM HEADLIGHT)
7.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Proceed to
OK
NG



OK

END (HEADLAMP UNIT LH WAS DEFECTIVE)

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

8.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CHECK OPERATION (HIGH BEAM HEADLIGHT)
9.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Result Proceed to
OK A
NG (w/ Adaptive High Beam System) B
NG (w/o Adaptive High Beam System) C



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

10.INSPECT HEADLIGHT UNIT ASSEMBLY RH

C

11.INSPECT HEADLIGHT UNIT ASSEMBLY RH
10.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E471200C01
2.042,0.448 2.406,0.75 0.365,0.302 5.219,0.802 5.583,1.104 0.365,0.302 1.521,2.115 1.802,1.667 true 1.792,1.406 1.573,0.927 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 2.177,0.521 2.49,0.719 0.313,0.198 10 false B 5.365,0.906 5.677,1.104 0.313,0.198 10 false H 1.271,0.75 1.948,0.969 0.677,0.219 10 false PSWL1- 1.229,2.156 1.906,2.375 0.677,0.219 10 false PSWL1+
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)


a.

Remove the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-13 (PSWL1+) - H-6 Always Below 1 Ω
B-3 (PSWL1-) - H-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

11.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E471204C01
1.875,0.479 2.271,0.719 0.396,0.24 4.979,0.615 5.375,0.854 0.396,0.24 5.052,2.281 5.448,2.521 0.396,0.24 1.823,2.219 2.219,2.458 0.396,0.24 1.938,1.854 1.656,1.521 true 1.615,1.271 1.396,0.792 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 1.135,2.125 1.448,2.323 0.313,0.198 10 false *c 2.031,0.542 2.344,0.74 0.313,0.198 10 false B 5.156,0.677 5.469,0.875 0.313,0.198 10 false H 1.104,0.625 1.781,0.844 0.677,0.219 10 false PSWL1- 2.021,1.813 2.698,2.031 0.677,0.219 10 false PSWL1+ 4.427,0.406 4.74,0.604 0.313,0.198 10 false *b 2.01,2.281 2.323,2.479 0.313,0.198 10 false I 5.219,2.344 5.531,2.542 0.313,0.198 10 false J 4.479,2.094 4.792,2.292 0.313,0.198 10 false *b
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)
*c Component without harness connected
(to Headlight Unit Assembly RH)
- -


a.

Remove the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-19 (PSWL1+) - C-5 Always Below 1 Ω
B-4 (PSWL1-) - C10 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HEADLIGHT UNIT RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

12.CHECK HEADLIGHT UNIT RH
a.

Replace the headlight unit RH with a know good one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

13.CHECK OPERATION (HIGH BEAM HEADLIGHT)
13.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Proceed to
OK
NG



OK

END (HEADLAMP UNIT RH WAS DEFECTIVE)

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH