Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P001400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1  P001500  Camshaft Position "B" - Timing Over-Retarded Bank 1  P002400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2  P002500  Camshaft Position "B" - Timing Over-Retarded Bank 2  


DESCRIPTION

HINT:

If DTC P001400, P001500, P002400 or P002500 is output, check the VVT (Variable Valve Timing) system.


The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the VVT and crankshaft position sensors and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

A192077E14
4.483,0.815 5.318,1.026 0.834,0.211 10 VVT Sensor 4.483,1.325 6.234,1.485 1.751,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.765,3.922 2.166,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.483,1.827 5.818,1.981 1.334,0.154 10 Mass Air Flow Meter 4.483,2.854 6.799,3.042 2.316,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.049,2.511 1.566,0.167 10 Throttle Position Sensor 4.483,3.353 5.929,3.506 1.446,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.067,5.101 1.184,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on SAE: P0014
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on SAE: P0015
P002400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2 Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on SAE: P0024
P002500 Camshaft Position "B" - Timing Over-Retarded Bank 2 Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on SAE: P0025

MONITOR DESCRIPTION

1.

The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, camshaft timing oil control valve and VVT controller.

2.

The ECM sends a target duty cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as a VVT controller being stuck and stores a DTC.

Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After the above condition 1 is met, the OCV is forcibly activated 63 times or more (when the vehicle is idling, this takes approximately 100 seconds).


3.

These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve malfunctions or the presence of foreign objects in the camshaft timing oil control valve.


CONFIRMATION DRIVING PATTERN

A232050E42
6.719,2.625 6.333,3.49 6.333,3.49 6.25,3.49 false 4.156,2.646 3.833,3.51 3.833,3.51 3.771,3.51 false 1.365,2.354 1.604,2.5 0.24,0.146 10 [A] 1.875,2.042 2.115,2.188 0.24,0.146 10 [B] 3.01,1.031 3.25,1.177 0.24,0.146 10 [C] 4.052,2.313 4.292,2.458 0.24,0.146 10 [D] 4.281,3.135 4.521,3.281 0.24,0.146 10 [E] 5.448,2.219 5.688,2.365 0.24,0.146 10 [F]* 6.615,2.302 6.854,2.448 0.24,0.146 10 [G] 6.833,3.156 7.073,3.302 0.24,0.146 10 [H] 0.156,2.313 1.125,2.646 0.969,0.333 10 Ignition Switch ON 0.708,2.052 1.094,2.24 0.385,0.188 10 Idling 0.177,1.094 1.135,1.438 0.958,0.344 10 Approximately 60 km/h 0.167,0.375 1.115,0.542 0.948,0.167 10 Vehicle Speed 1.615,2.771 2.417,2.969 0.802,0.198 10 Warming up 2.563,2.771 3.802,2.917 1.24,0.146 10 10 minutes or more 2.552,3.427 3.844,3.604 1.292,0.177 10 3 minutes or more 2.375,0.021 7.031,0.542 4.656,0.521 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5,3.385 6.188,3.563 1.188,0.177 10 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P001400, P001500, P002400 or P002500.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
Bank 1 P001400 P001500
Bank 2 P002400 P002500

·

If DTC P001400 or P001500 is output, check the bank 1 VVT system for the exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P002400 or P002500 is output, check the bank 2 VVT system for the exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400, P001500, P002400 OR P002500)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001400, P001500, P002400 or P002500 is output A
P001400, P001500, P002400 or P002500 and other DTCs are output B


HINT:

If any DTCs other than P001400, P001500, P002400 or P002500 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Warm up the engine.


c.

Turn the A/C on.


d.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5
Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
50004 372 46
OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 2, and Exhaust VVT Change Angle Bank 2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST SIDE)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Clear the DTCs

Powertrain > Engine > Clear DTCs
50002 372

b.

Warm up the engine.


c.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


d.

Read the DTCs using the GTS.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B


HINT:

DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.




A

B

5.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST SIDE)
a.

Inspect the camshaft timing oil control valve (for exhaust camshaft).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.
A385296C01
1.26,0.813 1.5,0.365 true 1.24,1.083 1.5,0.365 true 1.969,1.458 2.188,0.875 true 1.969,1.448 2.167,1.219 true 2.854,3.271 3.125,2.844 true 2.865,3.229 3.052,2.833 true 2.865,3.25 3.042,2.615 true 2.208,2.51 2.479,2.135 true 2.219,2.906 2.469,2.135 true 1.531,0.208 1.844,0.406 0.313,0.198 10 false *1 1.854,1.5 2.167,1.698 0.313,0.198 10 false *1 2.719,3.25 3.031,3.448 0.313,0.198 10 false *1 2.448,1.99 2.76,2.188 0.313,0.198 10 false *1
*1 Timing Mark


Remove the cylinder head cover RH and LH.


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.


c.

Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.


OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



d.

Reinstall the cylinder head cover RH and LH.


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

9.CHECK ENGINE MECHANICAL SYSTEM
6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
A225778C03
0.042,0 0.354,0.198 0.313,0.198 10 false *1 0.031,2.344 0.344,2.542 0.313,0.198 10 false *2
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


a.

Remove the No. 1 or No. 2 oil pipe.


b.

Remove the oil control valve filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



d.

Reinstall the oil control valve filter.


e.

Reinstall the No. 1 or No. 2 oil pipe.


Result:
Proceed to
OK
NG



OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

CLEAN OIL CONTROL VALVE FILTER AND OIL PIPE

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Clear the DTCs

Powertrain > Engine > Clear DTCs
50002 372

b.

Warm up the engine.


c.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


d.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B


HINT:

DTC P001400, P001500, P002400 or P002500 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




A

SYSTEM IS OK

B

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B




A

B