Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CAMSHAFT
RM38G0E _51 Engine / Hybrid System _101207 1GR-FE ENGINE MECHANICAL _0469483 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487752N01
0.75,2.417 1.354,2.417 true 4.906,0.656 5.51,0.656 true 0.563,2.292 0.844,2.646 0.281,0.354 18 false 1 5.573,0.51 5.854,0.865 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FAN SHROUD 16711 - - -
2 INTAKE AIR SURGE TANK 17129 - - -

A487753N01
0.083,0.302 7.083,2.385 7,2.083 0.083,2.417 2.198,4.313 2.115,1.896 1.083,1.781 1.167,1.927 1.167,1.927 1.354,1.927 true 1.552,4.802 2.125,4.802 true 0.5,2.052 0.927,2.052 true 1.365,1.479 1.219,1.26 1.219,1.26 1.063,1.26 true 6,2.042 6.25,2.042 true 5.573,2.271 5.823,2.271 true 5.365,1.813 5.615,1.813 true 2.167,1.26 2.531,1.26 true 4.219,1.385 4.573,1.385 true 5.729,4.688 6.115,4.688 true 1.438,2.99 1.438,2.74 true 1.094,2.885 1.198,2.885 1.198,2.885 1.198,2.74 true 1.771,2.833 1.646,2.833 1.646,2.833 1.646,2.677 true 1.448,4.01 1.448,3.76 true 0.083,3.354 2.188,3.354 false 0.396,1.958 0.677,2.313 0.281,0.354 10 false ● 0.625,1.646 0.875,1.885 0.25,0.24 10 false x 4 0.198,0.365 0.448,0.604 0.25,0.24 12 false *A 2.958,0.771 3.208,1.01 0.25,0.24 10 false x 3 1.688,1.802 1.979,2.125 0.292,0.323 18 false 3 0.927,1.167 1.208,1.521 0.281,0.354 10 false ● 6.615,1.885 6.906,2.188 0.292,0.302 18 false 4 6.104,1.813 6.354,2.052 0.25,0.24 10 false x 4 5.458,2.177 5.74,2.531 0.281,0.354 10 false ● 5.26,1.719 5.542,2.073 0.281,0.354 10 false ● 1.99,1.135 2.26,1.438 0.271,0.302 18 false 5 4.042,1.26 4.313,1.563 0.271,0.302 18 false 6 5.156,1.052 5.406,1.292 0.25,0.24 10 false x 3 5.708,4.698 5.958,4.938 0.25,0.24 10 false x 6 6.063,4.302 6.313,4.542 0.25,0.24 10 false x 6 6.427,4.583 6.719,4.885 0.292,0.302 18 false 7 2.177,4.677 2.469,4.979 0.292,0.302 18 false 8 1.385,3.01 1.677,3.313 0.292,0.302 18 false 9 0.948,2.813 1.188,3.021 0.24,0.208 10 false *1 1.802,2.75 2.042,2.958 0.24,0.208 10 false *2 1.396,4.021 1.688,4.323 0.292,0.302 18 false 9 0.146,2.458 0.396,2.698 0.25,0.24 12 false *B 0.156,3.406 0.406,3.646 0.25,0.24 12 false *C

Procedure Part Name Code
Z101186

Z101188

Z101187

3 AIR TUBE 17361 (Click here) - -
4 NO. 2 AIR TUBE 17362 (Click here) - -
5 NO. 1 EMISSION CONTROL VALVE SET 25701B - - -
6 NO. 2 EMISSION CONTROL VALVE SET 25702B - - -
7 IGNITION COIL ASSEMBLY 19500 (Click here) - -
8 VANE PUMP ASSEMBLY 44310 - - -
9 NO. 2 IDLER PULLEY SUB-ASSEMBLY 16604 - - -

*A w/ Secondary Air Injection System *B for Separate Type
*C for Integrated Type - -
*1 NO. 2 IDLER PULLEY COVER PLATE *2 IDLER PULLEY COVER PLATE
● Non-reusable part - -

A487754N01
0.958,4.344 1.219,4.156 1.219,4.156 1.427,4.156 true 3.74,4.604 3.74,4.333 true 5.667,4.469 5.625,4.208 5.625,4.208 5.396,4.208 true 5.083,5.219 5.385,5.219 true 5.5,3.115 5.667,2.958 5.667,2.958 5.802,2.958 true 5.823,3.417 6.125,3.417 true 4.521,3.375 4.823,3.375 true 4.781,2.969 5.25,2.969 true 5.104,2.979 5.156,3.167 5.156,3.167 5.333,3.167 true 0.948,2.281 1.365,2.281 true 0.938,1.948 0.896,1.688 0.896,1.688 0.667,1.688 true 1.552,2.208 1.854,2.208 true 1.354,1.813 1.125,1.313 1.125,1.313 0.823,1.313 true 1.052,1.906 1.052,1.313 true 3.854,0.688 4.25,0.688 true 5.542,1.302 5.823,1.302 true 5.365,0.667 5.646,0.667 true 1.906,1.156 1.677,0.552 1.677,0.552 1.375,0.552 true 2.104,0.615 2.385,0.615 true 2.885,1.531 3.167,1.531 true 2.906,2.479 3.188,2.479 true 3.104,5.24 3.406,5.24 true 2.781,5.521 3.083,5.521 true 1.375,5.438 1.583,5.438 1.583,5.438 1.854,5.188 true 3.74,4.625 4.292,4.979 0.552,0.354 18 false 10 3.656,3.833 4.208,4.188 0.552,0.354 10 false x 3 5.104,4.083 5.656,4.438 0.552,0.354 18 false 11 6.604,5.115 7.01,5.417 0.406,0.302 10 false x 2 4.927,5.146 5.167,5.323 0.24,0.177 10 false *1 3.448,5.104 4,5.458 0.552,0.354 18 false 12 1.469,4.021 2.021,4.375 0.552,0.354 18 false 13 0.458,4.604 0.865,4.906 0.406,0.302 10 false x 3 6.094,2.844 6.646,3.198 0.552,0.354 18 false 14 6.167,3.333 6.406,3.51 0.24,0.177 10 false *2 4.417,3.281 4.656,3.458 0.24,0.177 10 false ● 4.656,2.865 4.896,3.042 0.24,0.177 10 false ● 0.625,2.177 1.177,2.531 0.552,0.354 18 false 15 0.5,1.615 0.74,1.792 0.24,0.177 10 false *3 1.927,2.115 2.167,2.292 0.24,0.177 10 false ● 0.698,1.208 0.938,1.385 0.24,0.177 10 false ● 3.552,0.563 4.104,0.917 0.552,0.354 18 false 16 5.896,1.167 6.448,1.521 0.552,0.354 18 false 17 4.073,1.667 4.479,1.969 0.406,0.302 10 false x 2 4.021,1.156 4.427,1.458 0.406,0.302 10 false x 8 1.052,0.438 1.604,0.792 0.552,0.354 18 false 18 2.427,0.521 2.896,0.74 0.469,0.219 10 false ● *4 5.688,0.563 6.156,0.781 0.469,0.219 10 false ● *4 1.531,1.052 1.938,1.354 0.406,0.302 10 false x 9 2.76,2.385 3,2.563 0.24,0.177 10 false ● 3.24,1.427 3.479,1.604 0.24,0.177 10 false ● 2.667,5.427 2.906,5.604 0.24,0.177 10 false ● 1.208,5.365 1.448,5.542 0.24,0.177 10 false *5

Procedure Part Name Code
Z101186

Z101188

Z101187

10 NO. 2 EXHAUST MANIFOLD HEAT INSULATOR 17168 (Click here) - -
11 GENERATOR ASSEMBLY 27060 - - -
12 ENGINE OIL LEVEL DIPSTICK GUIDE 11452 - - -
13 WATER BY-PASS PIPE SUB-ASSEMBLY 16206 - - -
14 NO. 1 OIL PIPE 15771 (Click here) - -
15 NO. 2 OIL PIPE 15772 (Click here) - -
16 FUEL PIPE SUB-ASSEMBLY - - - -
17 CYLINDER HEAD COVER SUB-ASSEMBLY LH 11202 - - -
18 CYLINDER HEAD COVER SUB-ASSEMBLY 11201 - - -

*1 GENERATOR BRACKET *2 OIL CONTROL VALVE FILTER LH
*3 OIL CONTROL VALVE FILTER RH *4 SEAL WASHER
*5 ENGINE OIL LEVEL DIPSTICK - -
● Non-reusable part - -

A487755N01
1.427,3.99 1.583,3.99 1.583,3.99 1.76,4.229 true 1.885,3.906 2.01,3.906 2.01,3.906 2.031,4.167 true 6.563,0.229 6.802,0.229 true 2.073,5.031 2.073,5.25 true 1.615,2.844 1.438,2.844 1.438,2.844 1.229,3.021 true 2.271,0.875 2.271,1.031 true 2.542,0.823 2.542,1.021 true 2.938,0.74 2.938,1.031 true 3.354,0.708 3.354,1.01 true 3.75,0.719 3.75,1.021 3.75,1.021 1.708,1.021 true 4.083,1.667 4.302,1.667 true 4.26,1.135 4.479,1.135 true 6.729,2.635 6.729,3.219 6.729,3.219 5.063,3.219 true 6.406,2.656 6.406,3.208 true 6.104,2.677 6.104,3.208 true 5.385,2.875 5.385,3.208 true 5.177,2.615 5.177,3.208 true 5.396,4.073 5.583,4.073 true 4.708,2 5.083,2 true 3.729,2.385 3.885,2.385 3.885,2.385 3.885,2.521 true 1.354,1.292 1.938,1.292 true 4.688,3.771 4.542,3.771 4.542,3.771 4.344,3.354 true 2.125,2.521 1.979,2.521 1.979,2.521 1.729,2.052 true 2.531,3.802 2.802,3.583 2.802,3.583 2.979,3.583 true 3.823,0.417 4.323,0.417 true 2.052,0.271 2.448,0.271 2.448,0.271 2.448,0.479 true 2.219,0.271 2.219,0.542 true 6.385,1.99 6.5,1.99 6.5,1.99 6.594,2.135 true 5.49,2.219 5.49,2.479 true 5.667,2.229 5.333,2.229 true 2.646,2.135 2.5,2.135 2.5,2.135 2.385,1.896 true 4.083,2.313 4.24,2.313 4.24,2.313 4.365,2.469 true 3.594,3.958 3.844,3.958 true 1.104,3.875 1.656,4.229 0.552,0.354 18 false 19 1.406,4.344 1.865,4.542 0.458,0.198 10 false x 4 1.781,3.813 2.24,4.01 0.458,0.198 10 false ● 6.25,0.104 6.625,0.49 0.375,0.385 18 false 20 2.052,5.281 2.604,5.635 0.552,0.354 18 false 21 1.729,5.042 2.188,5.24 0.458,0.198 10 false x 2 1.948,2.719 2.729,3.094 0.781,0.375 18 false 22, 26 1.406,0.896 1.958,1.25 0.552,0.354 18 false 23 4.604,1.531 5.156,1.885 0.552,0.354 18 false 24 4.813,1 5.365,1.354 0.552,0.354 18 false 25 4.771,3.094 5.323,3.448 0.552,0.354 18 false 27 5.063,3.958 5.615,4.313 0.552,0.354 18 false 28 4.396,1.875 4.948,2.229 0.552,0.354 18 false 29 3.406,2.271 3.958,2.625 0.552,0.354 18 false 30 1.01,1.156 1.563,1.51 0.552,0.354 18 false 30 5.063,3.615 5.615,3.969 0.552,0.354 18 false 31 2.438,2.385 2.99,2.74 0.552,0.354 18 false 31 3.948,0.094 4.406,0.292 0.458,0.198 10 false x 8 3.615,0.094 4.073,0.292 0.458,0.198 10 false x 8 4.365,0.313 4.823,0.51 0.458,0.198 10 false ● 1.927,0.188 2.385,0.385 0.458,0.198 10 false ● 6.635,1.938 7.094,2.135 0.458,0.198 10 false x 8 6.927,2.25 7.156,2.521 0.229,0.271 10 false x 8 6.271,1.906 6.729,2.104 0.458,0.198 10 false ● 5.688,2.135 6.146,2.333 0.458,0.198 10 false ● 3.01,3.49 3.469,3.688 0.458,0.198 10 false *1 3.417,3.885 3.875,4.083 0.458,0.198 10 false *2 2.698,2.052 3.156,2.25 0.458,0.198 10 false *3 3.927,2.24 4.385,2.438 0.458,0.198 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

19 TIMING CHAIN COVER PLATE 11324 - - -
20 SET NO. 1 CYLINDER TO TDC/COMPRESSION - (Click here) - -
21 NO. 1 CHAIN TENSIONER ASSEMBLY 13540 (Click here) - -
22 CHAIN SUB-ASSEMBLY (for Bank 1) 13506 (Click here) - -
23 CAMSHAFT BEARING CAP (for Bank 1) - (Click here) - -
24 NO. 2 CAMSHAFT 13512 (Click here) - -
25 CAMSHAFT 13511 (Click here) - -
26 CHAIN SUB-ASSEMBLY (for Bank 2) 13506 (Click here) - -
27 CAMSHAFT BEARING CAP (for Bank 2) - (Click here) - -
28 NO. 4 CAMSHAFT SUB-ASSEMBLY 13054 (Click here) - -
29 NO. 3 CAMSHAFT SUB-ASSEMBLY 13053 (Click here) - -
30 CAMSHAFT TIMING GEAR ASSEMBLY 13050 (Click here) - -
31 CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 13070A (Click here) - -

*1 NO. 2 CHAIN TENSIONER ASSEMBLY *2 NO. 3 CHAIN TENSIONER ASSEMBLY
*3 NO. 2 CHAIN SUB-ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of Ignition coil assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A358535

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 16711 1.REMOVE FAN SHROUD

Hide 17129 2.REMOVE INTAKE AIR SURGE TANK

Hide 17361 3.REMOVE AIR TUBE (w/ Secondary Air Injection System)

Z101186

Click here(Click here)

Hide 17362 4.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Z101186

Click here(Click here)

Hide 25701B 5.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 25702B 6.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 19500 7.REMOVE IGNITION COIL ASSEMBLY

Z101186

Click here(Click here)

Hide 44310 8.DISCONNECT VANE PUMP ASSEMBLY

Hide 16604 9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 17168 10.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Z101186

Click here(Click here)

Hide 27060 11.REMOVE GENERATOR ASSEMBLY

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16206 13.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 15771 14.REMOVE NO. 1 OIL PIPE

Z101186

Click here(Click here)

Hide 15772 15.REMOVE NO. 2 OIL PIPE

Z101186

Click here(Click here)

Hide 16.DISCONNECT FUEL PIPE SUB-ASSEMBLY

Hide 11202 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11324 19.REMOVE TIMING CHAIN COVER PLATE

a.
A487756


Hide 20.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A487757N01
0.385,0.01 0.667,0.365 0.281,0.354 18 false i

i.

Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover sub-assembly.



b.
A487758C01
0.646,1.406 0.865,1.406 0.865,1.406 1.323,1 true 6.49,1.406 6.313,1.406 6.313,1.406 5.885,1.125 true 0.365,0.031 0.99,0.51 0.625,0.479 18 false i, ii 5.24,0.031 5.604,0.302 0.365,0.271 10 false *A 1.823,0.031 2.188,0.302 0.365,0.271 10 false *B 0.479,1.313 0.844,1.583 0.365,0.271 10 false *a 6.531,1.302 6.896,1.573 0.365,0.271 10 false *a
*A for Bank 1 *B for Bank 2
*a Paint Mark - -


i.

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

HINT:

If the marks are not aligned, turn the crankshaft again to align the marks.



ii.

Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the chain sub-assembly.

HINT:

Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.




Hide 13540 21.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A487759C01
4.5,1.667 4.677,1.667 4.677,1.667 5,1.083 true 5.479,0.417 5.375,0.417 5.375,0.417 5.052,0.969 true 5.51,0.333 5.802,0.563 0.292,0.229 10 false *a 4.344,1.583 4.635,1.813 0.292,0.229 10 false *b 0.406,0.125 0.719,0.531 0.313,0.406 18 false i 3.906,0.125 4.219,0.531 0.313,0.406 18 false ii 0.385,1.917 0.698,2.323 0.313,0.406 18 false iii 3.875,1.917 4.188,2.323 0.313,0.406 18 false iv 3.135,0.74 3.344,0.938 0.208,0.198 10 true 0° 2.823,0.177 3.052,0.365 0.229,0.188 10 true 30°
*a Lever Hole *b Tensioner Hole


i.

Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

HINT:

This prevents the valves and pistons from interfering with each other.



ii.

Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.


iii.

Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover sub-assembly.


iv.

Remove the 2 bolts and No. 1 chain tensioner assembly.

NOTICE:

Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.




Hide 13506 22.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A487760C01
1.323,3.385 1.479,3.385 1.479,3.385 1.667,3.677 true 1.167,3.302 1.333,3.521 0.167,0.219 10 true *a 2.125,0.042 2.375,0.333 0.25,0.292 18 false i 0.458,2.375 0.708,2.667 0.25,0.292 18 false ii 4.073,2.375 4.323,2.667 0.25,0.292 18 false iii 4.25,0.844 4.469,1.031 0.219,0.188 10 true 30°
*a 5° to 10° - -


i.

Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain sub-assembly between the banks.

CAUTION:

As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.


NOTICE:

When turning the crankshaft, engine oil may spray out of the oil holes.



ii.

Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

NOTICE:

When turning the crankshaft, engine oil may spray out of the oil holes.



iii.

Remove the chain sub-assembly from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.




Hide 23.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A487761C01
4.813,0.896 5.688,0.896 true 5.813,1 5.323,1 5.323,1 5.323,0.906 true 5.469,0.667 5.104,0.385 5.104,0.385 4.948,0.385 true 4.635,0.844 4.813,1.01 0.177,0.167 10 false *2 0.552,1.344 0.802,1.542 0.25,0.198 10 false *a 0.563,1.573 0.833,1.75 0.271,0.177 10 false *b 3.354,1 3.604,1.198 0.25,0.198 10 false 1 3.26,1.531 3.51,1.729 0.25,0.198 10 false 2 3.469,1.521 3.719,1.719 0.25,0.198 10 false 3 3.271,0.146 3.521,0.344 0.25,0.198 10 false 4 3.344,0.552 3.594,0.75 0.25,0.198 10 false 5 3.583,0.552 3.833,0.75 0.25,0.198 10 false 6 1.073,1.083 1.323,1.281 0.25,0.198 10 false 7 1.156,1.448 1.406,1.646 0.25,0.198 10 false 8 1.167,0.167 1.417,0.365 0.25,0.198 10 false 9 1.021,0.531 1.271,0.729 0.25,0.198 10 false 10 1.01,0.74 1.26,0.938 0.25,0.198 10 false 11 0.906,1.448 1.156,1.646 0.25,0.198 10 false 12 2.771,1.135 3.021,1.333 0.25,0.198 10 false 13 2.521,1.542 2.771,1.74 0.25,0.198 10 false 14 2.656,0.115 2.906,0.313 0.25,0.198 10 false 15 2.771,0.51 3.021,0.708 0.25,0.198 10 false 16 2.781,0.729 3.031,0.927 0.25,0.198 10 false 17 2.719,1.542 2.969,1.74 0.25,0.198 10 false 18 4.792,0.323 5.052,0.51 0.26,0.188 10 false *1 1.604,1.135 1.854,1.333 0.25,0.198 10 false 19 1.906,1.521 2.156,1.719 0.25,0.198 10 false 20 1.813,0.094 2.063,0.292 0.25,0.198 10 false 21 1.604,0.448 1.854,0.646 0.25,0.198 10 false 22 1.604,0.667 1.854,0.865 0.25,0.198 10 false 23 1.708,1.521 1.958,1.719 0.25,0.198 10 false 24 0.375,0.063 0.656,0.417 0.281,0.354 18 false i
*1 Bolt *2 Washer
*a Part Removal *b Installation of Bolts and Washers for Temporary Installation of Camshaft Housing


i.

Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing a camshaft bearing cap, install bolts and washers for temporary installation of the camshaft housing RH in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not install the camshaft bearing caps when installing bolts and washers for temporary installation of the camshaft housing RH.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing RH to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing RH into the cylinder head sub-assembly.



HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)





Hide 13512 24.REMOVE NO. 2 CAMSHAFT

a.
A487762N01
0.552,0.083 0.833,0.438 0.281,0.354 18 false i 4.365,0.042 4.563,0.302 0.198,0.26 18 true ii 2.927,1.677 3.135,1.938 0.208,0.26 18 true iii

i.

Remove the bolt of the No. 2 chain tensioner assembly.


ii.

Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.


iii.

While lifting up the No. 2 camshaft, pass it through the No. 2 chain sub-assembly and pull it out towards the front of the vehicle to remove it.



Hide 13511 25.REMOVE CAMSHAFT

a.
A487763N01
0.5,0.021 1.042,0.396 0.542,0.375 18 false i, ii 4.083,0.042 4.625,0.417 0.542,0.375 18 false iii

i.

Lift up the rear of the camshaft so that it is at an angle.


ii.

Remove the chain sub-assembly from the camshaft timing gear and pull out the camshaft and No. 2 chain sub-assembly towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and timing chain cover sub-assembly.



iii.

Suspend the chain with a string or equivalent.



Hide 13506 26.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A487764N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i 3.927,0.052 4.198,0.406 0.271,0.354 18 false ii

i.

Turn the crankshaft pulley counterclockwise and align the notch with the "0" timing mark of the timing chain cover sub-assembly.


ii.

Remove the chain sub-assembly from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.




Hide 27.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A487765C01
5.99,0.865 6.656,0.865 true 5.74,1.073 6.698,1.073 true 6.01,1.083 6.01,1.188 6.01,1.188 5.625,1.188 true 0.552,0.052 0.833,0.406 0.281,0.354 18 false i 1.083,0.979 1.365,1.333 0.281,0.354 10 false 1 6.719,0.781 7,1.135 0.281,0.354 10 false *1 6.729,1 6.906,1.188 0.177,0.188 10 true *2 0.531,1.323 0.813,1.677 0.281,0.354 10 false *a 0.542,1.552 0.833,1.781 0.292,0.229 10 false *b 1.24,1.406 1.427,1.604 0.188,0.198 10 false 2 4.5,0.052 4.792,0.406 0.292,0.354 18 false i 1.24,1.615 1.448,1.771 0.208,0.156 10 false 3 1.26,0.063 1.469,0.219 0.208,0.156 10 false 4 1.083,0.458 1.271,0.615 0.188,0.156 10 false 5 0.865,0.458 1.052,0.615 0.188,0.156 10 false 6 3.26,0.979 3.448,1.135 0.188,0.156 10 false 7 3.063,1.396 3.323,1.573 0.26,0.177 10 false 8 3.052,0.094 3.313,0.271 0.26,0.177 10 false 9 3.208,0.417 3.469,0.594 0.26,0.177 10 false 10 3.208,0.625 3.469,0.802 0.26,0.177 10 false 11 3.021,1.604 3.281,1.781 0.26,0.177 10 false 12 1.646,1.042 1.906,1.219 0.26,0.177 10 false 13 1.896,1.406 2.156,1.583 0.26,0.177 10 false 14 1.844,0.083 2.104,0.26 0.26,0.177 10 false 15 1.625,0.448 1.885,0.625 0.26,0.177 10 false 16 1.625,0.646 1.885,0.823 0.26,0.177 10 false 17 1.885,1.615 2.146,1.771 0.26,0.156 10 false 18 2.688,1.073 2.948,1.229 0.26,0.156 10 false 19 2.458,1.406 2.719,1.563 0.26,0.156 10 false 20 2.552,0.083 2.813,0.24 0.26,0.156 10 false 21 2.698,0.438 2.958,0.594 0.26,0.156 10 false 22 2.708,0.635 2.969,0.792 0.26,0.156 10 false 23 2.458,1.625 2.719,1.781 0.26,0.156 10 false 24
*1 Bolt *2 Washer
*a Part Removal *b Installation of Bolts and Washers for Temporary Installation of Camshaft Housing


i.

Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing a camshaft bearing cap, install bolts and washers for temporary installation of the camshaft housing LH in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not install the camshaft bearing caps when installing bolts and washers for temporary installation of the camshaft housing LH.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing LH to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing LH into the cylinder head sub-assembly.



HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)





Hide 13054 28.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

a.
A487766N01
0.479,0.063 0.76,0.417 0.281,0.354 18 false i 4.479,0.031 4.708,0.333 0.229,0.302 18 true ii 2.677,1.656 2.906,1.958 0.229,0.302 18 true iii

i.

Remove the bolt of the No. 3 chain tensioner assembly.


ii.

Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft sub-assembly.


iii.

While lifting up the No. 4 camshaft sub-assembly, pass it through the No. 2 chain sub-assembly and pull it out towards the front of the vehicle to remove it.



Hide 13053 29.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

a.
A487767N01
0.573,0.031 0.99,0.302 0.417,0.271 18 true i, ii 4.146,0.031 4.354,0.302 0.208,0.271 18 true iii

i.

Lift up the rear of the No. 3 camshaft sub-assembly so that it is at an angle.


ii.

Remove the chain sub-assembly from the camshaft timing gear and pull out the No. 3 camshaft sub-assembly and No. 2 chain sub-assembly towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and timing chain cover sub-assembly.



iii.

Suspend the chain with a string or equivalent.



Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A487768C01
3.156,1.427 3.771,1.552 3.771,1.552 3.281,1.042 true 1.677,1.438 2.24,1.438 true 2.906,0.948 2.365,0.948 true 4.094,0.385 3.927,0.385 3.927,0.385 3.813,0.854 true 4.115,0.313 4.365,0.573 0.25,0.26 10 false *1 1.51,1.375 1.802,1.646 0.292,0.271 10 false *2 2.208,0.875 2.458,1.073 0.25,0.198 10 false *a 2.365,0.01 2.823,0.313 0.458,0.302 18 false i, ii 3.823,1.521 4.073,1.719 0.25,0.198 10 false *a
*1 Straight Pin *2 Flange Bolt
*a Do Not Remove - -


i.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



ii.

Remove the flange bolt and camshaft timing gear assembly.

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear assembly, be sure to release the straight pin lock before installing the camshaft timing gear assembly.





Hide 13070A 31.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A487769C01
3.135,1.51 3.604,1.521 3.604,1.521 3.219,1.208 true 2.813,1.208 2.438,0.792 2.438,0.792 2.854,0.938 true 1.75,1.469 2.24,1.469 true 3.76,0.844 3.906,0.427 3.906,0.427 4.042,0.427 true 1.583,1.406 1.823,1.573 0.24,0.167 10 false *2 3.656,1.469 3.948,1.688 0.292,0.219 10 false *a 2.344,0.021 2.854,0.385 0.51,0.365 18 false i, ii 4.094,0.344 4.333,0.542 0.24,0.198 10 false *1 2.281,0.667 2.573,0.885 0.292,0.219 10 false *a
*1 Straight Pin *2 Flange Bolt
*a Do Not Remove - -


i.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



ii.

Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the camshaft timing exhaust gear assembly, be sure to release the straight pin lock before installing the camshaft timing exhaust gear assembly.