Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P032511  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground  P032515  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open  P033011  Knock Sensor 2 Bank 2 Circuit Short to Ground  P033015  Knock Sensor 2 Bank 2 Circuit Short to Battery or Open  


DESCRIPTION

A flat-type knock control sensor (non-resonant type) has a structure that can detect vibration between approximately 5 kHz and 23 kHz.

The knock control sensors are fitted onto the engine block to detect engine knocking.

The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P032511 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground Output voltage of knock control sensor (bank 1) is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor (bank 1) circuit

·

Knock control sensor (bank 1)

·

ECM


Comes on SAE: P0327
P032515 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open Output voltage of knock control sensor (bank 1) is higher than 4.5 V for 1 second or more (1 trip detection logic).
·

Open in knock control sensor (bank 1) circuit

·

Knock control sensor (bank 1)

·

ECM


Comes on SAE: P0328
P033011 Knock Sensor 2 Bank 2 Circuit Short to Ground Output voltage of knock control sensor (bank 2) is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor (bank 2) circuit

·

Knock control sensor (bank 2)

·

ECM


Comes on SAE: P0332
P033015 Knock Sensor 2 Bank 2 Circuit Short to Battery or Open Output voltage of knock control sensor (bank 2) is higher than 4.5 V for 1 second or more (1 trip detection logic).
·

Open in knock control sensor (bank 2) circuit

·

Knock control sensor (bank 2)

·

ECM


Comes on SAE: P0333

HINT:

When DTC P032511, P032515, P033011 or P033015 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

MONITOR DESCRIPTION

If the output voltage transmitted by the knock control sensor remains low or high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P032511, P032515, P033011 or P033015.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A337226E07
0.396,1.354 0.771,1.552 0.375,0.198 10 false C103 0.396,1.5 2.49,1.802 2.094,0.302 10 false Knock Control Sensor (Bank 1) 0.5,0.896 0.813,1.094 0.313,0.198 10 false 1 1.906,0.885 2.219,1.083 0.313,0.198 10 false 2 3.521,4.625 3.833,4.823 0.313,0.198 10 false * 0.448,5.208 1.25,5.438 0.802,0.229 10 false *: Shielded 5.74,1.646 6.26,1.906 0.521,0.26 10 false EKNK 6.063,4.792 6.375,4.99 0.313,0.198 10 false C92 5.49,1.656 5.885,1.896 0.396,0.24 10 false 93 5.5,0.875 5.896,1.115 0.396,0.24 10 false 94 5.74,0.875 6.26,1.135 0.521,0.26 10 false KNK1 0.417,3.75 0.958,3.969 0.542,0.219 10 false C102 0.406,3.906 2.5,4.208 2.094,0.302 10 false Knock Control Sensor (Bank 2) 0.49,3.271 0.802,3.469 0.313,0.198 10 false 1 1.927,3.271 2.24,3.469 0.313,0.198 10 false 2 5.396,3.26 5.792,3.5 0.396,0.24 10 false 117 5.74,3.25 6.26,3.51 0.521,0.26 10 false KNK2 5.75,4.052 6.271,4.313 0.521,0.26 10 false EKN2 5.406,4.063 5.802,4.302 0.396,0.24 10 false 116 6.063,4.969 6.49,5.229 0.427,0.26 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

DTCs P032511 and P032515 are for the bank 1 knock control sensor circuit.

·

DTCs P033011 and P033015 are for the bank 2 knock control sensor circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (KNOCK F/B VALUE)
a.

Start the engine.


b.

Warm up the engine.


c.

Read the value while driving the vehicle.

Powertrain > Engine > Data List
Tester Display
Knock F/B Value
50003 372 96
OK:

The value changes.


HINT:
Malfunction does not occur Knock F/B Value changes
Malfunctions occur Knock F/B Value does not change

The Knock F/B Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)

OK

3.INSPECT KNOCK CONTROL SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
3.INSPECT KNOCK CONTROL SENSOR
a.

Inspect the knock control sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>KNOCK SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock control sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
a.

Disconnect the knock control sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C103,C92,C102)Location & Routing

Click Connector(C103)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Knock Control Sensor (Bank 1)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C102)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Knock Control Sensor (Bank 2)

C103-2 - C92-94 (KNK1) Always Below 1 Ω
C103-1 - C92-93 (EKNK) Always Below 1 Ω
C102-2 - C92-117 (KNK2) Always Below 1 Ω
C102-1 - C92-116 (EKN2) Always Below 1 Ω
C103-2 or C92-94 (KNK1) - Body ground and other terminals Always 10 kΩ or higher
C103-1 or C92-93 (EKNK) - Body ground and other terminals Always 10 kΩ or higher
C102-2 or C92-117 (KNK2) - Body ground and other terminals Always 10 kΩ or higher
C102-1 or C92-116 (EKN2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR